 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| color tv/dvd/vcr triple combo ewc19t3 (19 inch) EWC27T3 (27 inch) owner? manual as an e nergy s tar partner, our company has determined that this product meets the e nergy s tar guidelines for energy efficiency. e nergy s tar is a u.s. registered mark. if you need additional operating assistance after reading this owner s manual or to order replacement accessories, please call toll free : 1-800-256-2487. or visit our web site at http://www.funai-corp.com please read before using this equipment instrucciones en espa ? ol incluidas. this owner s manual is made of recycled paper. supplied accessories batteries remote control unit accessories 2 aa batteries ne211ud part no. emerson and the g-clef logo are registered trademarks of emerson radio corp., parsippany, new jersey, u.s.a. 27 model illustrated owner s manual 0emn02182 td853/953(p01-35).qx33 03.2.28 10:59 pm page 1
1.read instructions- all the safety and operating instructions should be read before the appliance is operated. 2.retain instructions- the safety and operating instructions should be retained for future reference. 3.heed warnings -all warnings on the appliance and in the operating instructions should be adhered to. 4.follow instructions- all operating and use instructions should be followed. 5.cleaning- unplug tv/dvd/vcr from the wall outlet before cleaning. do not use liquid cleaners or aerosol cleaners. use a damp cloth for cleaning. exception: a product that is meant for uninterrupted service and, that for some specific reason, such as the possi- bility of the loss of an authorization code for a catv con- verter, is not intended to be unplugged by the user for clean- ing or any other purpose, may exclude the reference to unplugging the appliance in the cleaning description other- wise required in item 5. 6.attachments- do not use attachments not recommended by the tv/dvd/vcr manufacturer as they may cause hazards. 7.water and moisture- do not use this tv/dvd/vcr near water-for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool, and the like. 8.accessories- do not place this tv/dvd/vcr on an unstable cart, stand, tripod, bracket, or table. the tv/dvd/vcr may fall, causing serious injury to someone, and serious damage to the appliance. use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the tv/dvd/vcr. any mounting of the appliance should follow the manufacturer s instructions and should use a mounting accessory recommended by the manufacturer. an appliance and cart combination should be moved with care.quick stops, excessive force, and uneven surfaces may cause the appliance and cart combination to overturn. ameubles- cet appareil ne doit ? tre plac ? que sur un meuble (avec ou sans roulettes) recommand ? par le fabricant. si vous l installez sur un meuble ? roulettes, d ? placez les deux ensembles avec pr ? caution. un arr ? t brusque, l utilisation d une force excessive et des sur- faces irr ? guli ? res risquent de d ? sta- biliser l ensemble et de le renverser. 9. ventilation- slots and openings in the cabinet and the back or bottom are provided for ventilation and to ensure reliable operation of the tv/dvd/vcr and to protect it from over- heating, and these openings must not be blocked or cov- ered. the openings should never be blocked by placing the tv/dvd/vcr on a bed, sofa, rug, or other similar surface. this tv/dvd/vcr should never be placed near or over a radiator or heat register. this tv/dvd/vcr should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer s instructions have been adhered to. 10.power sources- this tv/dvd/vcr should be operated only from the type of power source indicated on the mark- ing label. if you are not sure of the type of power supply to your home, consult your appliance dealer or local power company. for tv/dvd/vcrs intended to operate from battery power, or other sources, refer to the operating instructions. 11.grounding or polarization- this tv/dvd/vcr is equipped with a polarized alternating-current line plug(a plug having one blade wider than the other). this plug will fit into the power outlet only one way. this is a safety fea- ture. if you are unable to insert the plug fully into the out- let, try reversing the plug. if the plug should still fail to fit, contact your electrician to replace your obsolete outlet. do not defeat the safety purpose of the polarized plug. 12.power-cord protection -power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying par- ticular attention to cords at plugs, convenience receptacles, and the point where they exit from the appliance. - 2 - en 1b15 warning: to reduce the risk of fire or electric shock, do not expose this appliance to rain or moisture. caution: to reduce the risk of electric shock, do not remove cover (or back). no user serviceable parts inside. refer servicing to qualified service person- nel. caution risk of electric shock do not open this symbol indicates that dan- gerous voltage constituting a risk of electric shock is present within this unit. this symbol indicates that there are important operating and maintenance instructions in the literature accompanying the appliance. the caution marking is located on the rear of the cabinet. important safeguards portable cart warning s3126a symbole d'avertissement pour les composantes appareil et meuble a roulettes s3126a td853/953(p01-35).qx33 03.2.28 10:59 pm page 2 - 3 - en 1b15 13.outdoor antenna grounding- if an outside antenna or cable system is connected to the tv/dvd/vcr, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. article 810 of the national electrical code, ansi/nfpa no. 70, provides information with respect to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. (fig. a) 14.lightning- for added protection for this tv/dvd/vcr receiver during a lightning storm, or when it is left unat- tended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. this will prevent damage to the tv/dvd/vcr due to lightning and power-line surges. 15.power lines- an outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. when installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. 16.overloading- do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock. 17.object and liquid entry- never push objects of any kind into this tv/dvd/vcr through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock. never spill liquid of any kind on the tv/dvd/vcr. 18.servicing- do not attempt to service this tv/dvd/vcr yourself as opening or removing covers may expose you to dangerous voltage or other hazards. refer all servicing to qualified service personnel. 19.damage requiring service- unplug this tv/dvd/vcr from the wall outlet and refer servicing to qualified service personnel under the following conditions: a. when the power-supply cord or plug is damaged or frayed. b. if liquid has been spilled, or objects have fallen into the tv/dvd/vcr. c. if the tv/dvd/vcr has been exposed to rain or water. d. if the tv/dvd/vcr does not operate normally by follow- ing the operating instructions. adjust only those controls that are covered by the operating instructions, as improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the tv/dvd/vcr to its normal operation. e. if the tv/dvd/vcr has been dropped or damaged in any way. f. when the tv/dvd/vcr exhibits a distinct change in per- formance-this indicates a need for service. 20.replacement parts- when replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer that have the same character- istics as the original part. unauthorized substitutions may result in fire, electric shock, injury to persons or other haz- ards. 21.safety check- upon completion of any service or repairs to this tv/dvd/vcr, ask the service technician to perform routine safety checks to determine that the tv/dvd/vcr is in proper operating condition. 22.heat- this tv/dvd/vcr product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat. ground clamps nec - national electrical code example of antenna grounding as per national electrical code s2898a wire discharge unit (nec section 810-20) grounding conductors (nec section 810-21) electrode system (nec art 250, part h) service equipment clamp antenna lead in antenna power service grounding ground electric figure a caution: to prevent electric shock, match wide blade of plug to wide slot, fully insert. attention: pour ? viter les choc ? lectriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu au fond. td853/953(p01-35).qx33 03.2.28 10:59 pm page 3 - 4 - en 1b15 radio-tv interference this equipment has been tested and found to com- ply with the limits for a class b digital device, pur- suant to part 15 of the fcc rules. these limits are designed to provide reasonable protection against harmful interference in a residential installation. this equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. however, there is no guarantee that interference will not occur in a particular installation. if this equipment does cause harmful interference to radio or television reception, which can be deter- mined by turning the equipment off and on, the user is encouraged to try to correct the interfer- ence by one or more of the following measures: 1) reorient or relocate the receiving antenna. 2) increase the separation between the equipment and receiver. 3) connect the equipment into an outlet on a cir- cuit different from that to which the receiver is connected. 4) consult the dealer or an experienced radio/tv technician for help. fcc warning- this equipment may gener- ate or use radio frequency energy. changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction man- ual. the user could lose the authority to oper- ate this equipment if an unauthorized change or modification is made. important copyright information unauthorized copying, broadcasting, public perfor- mance and lending of discs are prohibited. laser safety this unit employs a laser. only a qualified service person should remove the cover or attempt to ser- vice this device, due to possible eye injury. caution: use of controls or adjust- ments or performance of proce- dures other than those specified herein may result in hazardous radiation exposure. caution: visible and invisible laser radiation when open and interlock defeated. do not stare into beam. location: inside, near the deck mechanism. this class b digital apparatus complies with canadian ices-003. cet appareil num?rique de la classe b est con- forme ? la norme nmb-003 du canada. caution: to prevent electric shock, match wide blade of plug to wide slot, fully insert. attention: pour ? viter les choc ? lectriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu au fond. precautions td853/953(p01-35).qx33 03.2.28 10:59 pm page 4 - 5 - en 1c29 avoid the hazards of electrical shock and fire location for safe operation and satisfactory performance of your tv/dvd/vcr, keep the following in mind when selecting a place for its installation: shield it from direct sunlight and keep it away from sources of intense heat. avoid dusty or humid places. avoid places with insufficient ventilation for proper heat dissipation. do not block the ventilation holes at the top and bottom of the unit. do not place the unit on a carpet because this will block the ventilation holes. install unit in a horizontal position. avoid locations subject to strong vibration. do not place the tv/dvd/vcr near strong magnetic fields. avoid moving tv/dvd/vcr to locations where temperature differences are extreme. do not handle the power cord with wet hands. do not pull on the power cord when disconnecting it from an ac wall outlet. grasp it by the plug. if, by accident, water is spilled on your unit, unplug the power cord immediately and take the unit to our authorized service center for servicing. do not put your fingers or objects into the tv/dvd/vcr disc loading tray. do not place anything directly on top of the unit. warning moisture condensation may occur inside the unit when it is moved from a cold place to a warm place, or after heating a cold room or under conditions of high humidity. if a dvd is played in a tv/dvd/ vcr which has moisture, it may damage the dvd and tv/dvd/vcr. therefore when the condensation occurs inside the unit, turn the power on and allow at least 2 hours for the unit to dry out. the serial number of this product may be found on the back of the unit. no other tv/dvd/vcr has the same serial number as yours. you should record the number and other vital information here and retain this book as a permanent record of your purchase to aid identification in case of theft. serial numbers are not kept on file. date of purchase dealer purchase from dealer address dealer phone no. model no. serial no. a note about recycling this product s packaging materials are recyclable and can be reused. please dispose of any materials in accordance with your local recycling regulations. batteries should never be thrown away or incinerated but disposed of in accordance with your local regula- tions concerning chemical wastes. the following symbols below appear in some head- ings and notes in this manual, with the following meanings : description refers to tv/vcr operation (in the tv/vcr mode). : description refers to playback of dvd video discs (in the dvd mode). : description refers to playback of audio cds (in the dvd mode). : description refers to playback of mp3 discs (in the dvd mode). : description refers to the items to be set by the quick mode (in the dvd mode). quick mp3 cd dvd-v tv/vcr symbols used in this manual td853/953(p01-35).qx33 03.2.28 10:59 pm page 5 - 6 - en 1c29 table of contents c important safeguards . . .2, 3 c precautions . . . . . . . . . . . . . . . .4 location . . . . . . . . . . . . . . . . . . .5 avoid the hazards of electrical shock and fire .5 warning . . . . . . . . . . . . . . . . . . . .5 symbols used in this manual . . . . . . . . . . . . . . . . . . . . .5 c table of contents . . . . . . . . . .6 c features . . . . . . . . . . . . . . . . . . . .7 c operating controls and functions . . . . . . . . . . . . . . . .9, 10 c preparation for use . . . . . . .11 antenna/cable connection . . . . . . . . . . . . . . . .11 connecting to external input jacks . . . . . . . . . . . . . . . .12 installing the batteries . .12 external input mode . . . . . .12 connecting to a stereo system . . . . . . . . . . . . . . . . . . . .13 connecting to a stereo amplifier equipped with digi- tal input jacks such as md deck or dat deck (for dvd) .13 connecting to a dolby digital decoder or dts decoder (for dvd) . . .14 tv/vcr section c set up for use . . . . . . . . . . . . .15 channel set up for the first time . . . . . . . . .15 deleting (or adding) channel . . . . . . . . . . . . . . . . . . .15 channel set up again . . . . . .16 selecting the language . .16 daylight-saving time . . . . . .16 clock set up (auto / manual) . . . . . . . . .17, 18 c tv operation . . . . . . . . . . . . . . .19 watching a tv program . . .19 degaussing . . . . . . . . . . . . . . . .19 picture control . . . . . . . . . . .19 closed caption system . . . .20 v-chip set up . . . . . . . . . . . . . . .21 c mts(multi-channel television sound)system . . . . . . . . . . . . . . . .23 checking the selected mts mode . . . . . . . . . . . . . . . . . .23 mts recording/monitor mode . . . . . . . . . . . . . . . . . . . . . .23 selecting the mts system .24 c video cassette . . . . . . . . . . . . .25 c playback . . . . . . . . . . . . . . . . . . .26 normal playback . . . . . . . . .26 tracking adjustment . . . . .26 slow motion . . . . . . . . . . . . . .26 picture search . . . . . . . . . . . .26 still picture . . . . . . . . . . . . . .26 vertical hold control . . .26 c special playback . . . . . . . . . .27 rental playback . . . . . . . . . .27 auto repeat playback . . . . .27 c search . . . . . . . . . . . . . . . . . . . . .28 zero return . . . . . . . . . . . . . . .28 time search . . . . . . . . . . . . . . .28 index search . . . . . . . . . . . . . .29 c special features . . . . . . . . . .29 real time tape counter . . .29 auto rewind-eject . . . . . . . .29 c recording . . . . . . . . . . . . . . . . .30 normal recording . . . . . . . .30 skipping unwanted scenes during recording . . . . . . . . . . . . . . . . .30 otr (one touch recording) . . . . . .31 copying a video cassette (requires a vcr or camcorder) . . .31 c timer . . . . . . . . . . . . . . . . . . . . . .32 automatic timer recording . . . . . . . . . .32 timer program extension .33 hints for automatic timer recording . . . . . . . . . . . . . . . . .34 auto return . . . . . . . . . . . . . . .34 sleep timer . . . . . . . . . . . . . . . .34 c on screen display . . . . . . . . .35 c cable channel designations . . . . . . . . . . . . . .35 d vd section c about the discs . . . . . . . . . . . .36 playable discs . . . . . . . . . . . .36 disc types . . . . . . . . . . . . . . . . .36 c playing a disc . . . . . . . . . . . . . .37 basic playback . . . . . . . . . . . .37 general features . . . . . . . . .37 disc menu . . . . . . . . . . . . . . . . .37 title menu . . . . . . . . . . . . . . . . .37 resume . . . . . . . . . . . . . . . . . . . .38 pause . . . . . . . . . . . . . . . . . . . . . .38 step by step playback . . . . .38 fast forward/reverse search . . . . . . . . . . . . . . . . . . . .38 slow forward / slow reverse . . . . . . . . . . . . . . . . . . . .38 zoom . . . . . . . . . . . . . . . . . . . . . .38 c search function . . . . . . . . . . .39 track search . . . . . . . . . . . . .39 title / chapter search . . . .39 time search . . . . . . . . . . . . . . .39 marker setup screen . . . . . .39 c special playback function . . .40 repeat . . . . . . . . . . . . . . . . . . . . .40 program . . . . . . . . . . . . . . . . . . .40 random playback . . . . . . . . .40 c playing a mp3 disc . . . . . . . . . .41 mp3 playback . . . . . . . . . . . . . .41 track selection . . . . . . . . . . .41 program . . . . . . . . . . . . . . . . . . .41 random playback . . . . . . . . .41 c changing the settings . . . .42 subtitle language . . . . . . . .42 audio language . . . . . . . . . . .42 stereo sound mode . . . . . . . .42 camera angle . . . . . . . . . . . . .42 black level setting . . . . . . .42 virtual surround . . . . . . . . .42 c the on-screen information . . .43 c changing the dvd setup items . . . . . . . . . . . . . . . . . . . . . . .44 language setting . . . . . . . . .44 display setting . . . . . . . . . . . .45 audio settings . . . . . . . . . . . .45 parental control . . . . . . . . .46 c troubleshooting guide . . .47 c maintenance . . . . . . . . . . . . . . .50 disc handling . . . . . . . . . . . . .50 c specifications . . . . . . . . . . . . .51 c warranty . . . . . . . . . . .back cover td853/953(p01-35).qx33 03.2.28 10:59 pm page 6 - 7 - en 1c29 hi-fi system the hi-fi stereo recording system offers you excellent sound quality with a dynamic range of 80db, frequency response from 20hz to 20khz, and 0.005% wow and flutter. rotary 4-head record/playback system four heads ensure excellent picture quality and special effects playback. index search fast-forwards to start of next recording. slow motion view recorded program at slower than normal speed. infrared remote control trilingual on screen tv/vcr setup display selec- table in english or spanish or french real time counter this shows the elapsed recording or playback time in hours, minutes, and seconds. the indication will appear when the tape is rewound further than the tape counter position 0:00:00 . 181 channel capability pll frequency synthesiz- er tuner with direct station call (a converter may be necessary to view scrambled cable channels.) auto clock setting allows you to set the clock function from a pbs broadcast station. closed caption system you may view specially labeled (cc) tv programs, movies, news, prere- corded tapes, etc. with either a dialogue caption or text display added to the program. auto power on and off system automatically turns on the tv/dvd/vcr when you insert the cassette, turns off after auto-rewind, and ejects when the beginning of the tape is reached. auto rewind when the end of a tape is reached this function doesn t occur when using timer recording. smooth mode change tv/vcr mode, dvd mode automatically changes without control. 2 step picture search operation you can view a video program at a high speed or super high speed in either a forward or reverse direction in lp and slp mode. for sp mode only high speed. three different playback tape speeds : sp/lp/slp two different recording tape speeds : sp/slp auto head cleaner automatically cleans video heads as you insert or remove a cassette. zero return the tape returns to counter of 0:00:00 by rewinding or fast forwarding. still freeze the picture at any time, for close viewing of a particular scene. digital auto tracking (dtr) automatically adjusts the tracking for each tape you play. rental play mode improves playback picture quality from worn tapes, such as rental tapes. auto repeat allows you to repeat the playing of a tape indefinitely without pressing the play button. time search let you set the tv/dvd/vcr to advance the tape by entering the desired playback time you want to skip. otr (one touch recording) instant timed recording from 30 to 480 minutes is possible at the push of the rec/otr button. 1 year, 8 events (including daily and weekly timer recording) the built-in timer allows you to record up to 8 programs at different times on dif- ferent channels up to 1 year in advance. the daily timer allows recordings to be made of daily broad- casts, and the weekly timer allows recording to be made once a week up to the end of the tape. auto return after timer recording is finished, the tv/dvd/vcr can return to the beginning of the recording. sleep timer allows you to have the tv/dvd/vcr automatically turn on or off at a desired time. timer program extension allow you to shift the time schedule for automatic timer recording. v-chip enables parents to prevent their children from watching inappropriate material on tv. features tv/vcr mode a note about recycling this product s packaging materials are recyclable and can be reused. please dispose of any materials in accordance with your local recycling regulations. batteries should never be thrown away or incinerated but disposed of in accordance with your local regula- tions concerning chemical wastes. td853/953(p01-35).qx33 03.2.28 10:59 pm page 7 - 8 - en 1c29 ? dolby digital sound this player can handle dolby digital surround sound having 5.1 channels when connected to a dolby digital decoder . ? still/fast/slow/step playback various playback modes are available including still pictures, fast forward/reverse, slow motion and step frames. ? random playback for audio cd and mp3 this player can shuffle the order of tracks to play them in random order. ? program playback for audio cd and mp3 you can program the order of tracks to play them in any desired order. ? dvd menus in a desired language you can display dvd menus in a desired language, if available on a dvd. ? screen saver/auto power-off functions the screen saver program starts when there is no input from the player for five minutes in the stop mode. when the screen saver program is activated for 15 minutes, the power automatically turns off. ? subtitles in a desired language you can select a desired language for the display subtitles, if that language is available on a disc. ? selecting a camera angle you can select the desired camera angle, if a disc contains sequences recorded from different angles. ? choices for audio language and sound mode you can select the desired audio language and sound mode, if different languages and modes are available on a disc. ? parental lock you can set the control level to limit playback of discs which may not be suitable for children. ? automatic detection of discs this player automatically detects if the loaded disc is dvd, audio cd or mp3 on disc. ? playback mp3 disc ? on-screen display information about the current operation can be dis- played on a tv screen, allowing you to confirm the currently active functions (such as program play- back), on the tv screen using the remote control. ? search chapter search / title search / track search / time search ? repeat chapter / title / track / group / all / a-b ? zoom magnified screen can be displayed. ? marker the part designated by user can be called back. ? resume play user can resume to playback from the part at which the play was stopped. ? virtual surround ? bit rate indication ? drc (dynamic range control) you can control the range of sound volume. note: we do not recommend the use of universal remote controls. not all of the functions may be controlled with a universal remote control. if you decide to use a universal remote control with this tv/vcr/dvd, please be aware that the code num- ber given may not operate this tv/vcr/dvd. in this case, please call the manufacturer of the universal remote control. dvd mode td853/953(p01-35).qx33 03.2.28 10:59 pm page 8 - 9 - en 1c29 operating controls and functions 5. stop button [p.37] stops operation of the disc. 6. open/close button [dvd p.37] press to insert discs into or remove them from the tray. 7. disc loading tray 8. dvd indicator lights on during dvd mode. 9. select button press to change to tv/vcr mode, external input mode or dvd mode. 10. tv/vcr indicator lights on during tv/vcr mode. 11. channel k / l buttons press to select memorized channel. 12. recording indicator flashes during recording. lights up in the stand- by mode for timer recording. 13. rec/otr (record)button [tv/vcr p.30, 31] press for manual recording. activates one touch recording. (otr is only during tv/vcr mode.) 14. rew button (for tv/vcr) [tv/vcr p.26] press to rewind the tape, or to view the picture rapidly in reverse during playback mode. (rewind search) 15. fwd button (for tv/vcr) [tv/vcr p.26] press to rapidly advance the tape, or to view the picture rapidly in forward during playback mode. (forward search) 16. stop/eject button [tv/vcr p.28] press to stop the tape motion. press in the stop mode to remove tape from the tv/vcr/dvd. 17. remote sensor window 18. headphone jack to connect headphone (not supplied) for personal listening. 19. video input jack connect to the video output jack of a video camera or vcr. - remote control - [fig. 2] 1. power button [tv/vcr p.15 / dvd p.37] press to turn the power on and off. 2. volume x / y buttons press to control the volume level for the dvd and tv. 3. skip buttons (for dvd) [p.38] press once to skip chapters or tracks to a desired point. press and hold to change forward or reverse play- back speed. 4. play button [tv/vcr p.26 / dvd p.37] starts playback of the disc or tape contents. - tv/dvd/vcr front panel - [fig.1] 12 4 56 10 715 14 9 8 33 4 11 12 13 21 20 19 18 17 16 select tv/vcr dvd r l audio video headphone dvd buttons tv/vcr buttons a open/close p channel o i rec/otr c stop skip g b play h skip p volume o power search c stop f.fwd g b play h rew a eject pause play stop enter record disc menu return title setup a - b repeat search mode clear mode angle subtitle audio display speed c.reset power picture select sleep ch. vol. mute zoom 123 456 789 0 +10 +100 34 35 23 24 26 25 (dvd) 3 (tv/vcr) 14 13 27 28 30 31 33 32 29 4 36 37 38 41 3 (dvd) 15 (tv/vcr) 43 2 11 45 44 42 5 39 40 1 22 td853/953(p01-35).qx33 03.2.28 10:59 pm page 9 - 10 - en 1c29 ant. l audio out r coaxial 1 47 46 48 49 20. audio l/r input jacks connect to the audio output jacks of a video camera or vcr. 21. cassette compartment 22. picture button press to adjust the picture. 23. number buttons tv mode: [p.15] press two digits to directly access the desired channel. remember to press a "0" before a single digit channel. +100 button press to select cable channels which are equal or greater than number 100. dvd mode: press to enter the desired number. +10 button press to enter the desired numbers which are equal or greater than number 10. 24. pause button [tv/vcr p.26 / dvd p.38] pauses the current disc or tape operation. 25. speed button [tv/vcr p.30] press to choose the desired recording speed: sp/slp. 26. c.reset button [tv/vcr p.28] press to reset counter to 0:00:00. press to cancel a setting of timer program. (see page 33.) 27. display button tv/vcr mode: display the counter or the current channel number and current time on the tv screen. dvd mode: [p.43] displays the current status on the tv screen for checking purposes. 28. setup button [tv/vcr p.15] [dvd p.44-46] press to enter or exit the tv menu or dvd setup mode. 29. title button [dvd p.37] displays the title menu. 30. clear button resets a setting. 31. mode button [dvd p.41] activates program playback or random playback mode. 32. search mode button [dvd p.39] press to locate a desired point. 33. audio button [dvd p.42] press to select a desired audio language or sound mode. 34. subtitle button [dvd p.42] press to select a desired subtitle language. 35. repeat button [dvd p.42] repeats playback of the current disc, title, chapter or track. 36. angle button (dvd mode) [dvd p.42] press to change the camera angle to see the sequence being played back from a different angle. 37. a-b repeat button [dvd p.40] repeats playback of a selected section. 38. return button returns to the previous operation in the dvd setup mode. 39. enter button press to accept a setting. 40. arrow buttons tv/vcr mode: press to select a setting mode from the menu on the tv screen. press to select or adjust from a particular menu. dvd mode: use when making settings while watching the display on a tv screen. 41. disc menu button [dvd p.37] displays the menus in the dvd. 42. zoom button [dvd p.38] enlarges part of a dvd-reproduced image. 43. mute button mutes the sound. press it again to resume sound. 44. sleep button [tv/vcr p.34] sets the sleep timer. 45. select button press to switch tv/vcr and dvd mode. you can see the mode (tv/vcr or dvd) on the front panel indicator. - tv/dvd/vcr rear panel - [fig.3] td853/953(p01-35).qx33 03.2.28 11:00 pm page 10 - 11 - en 1c29 cable with converter/ descrambler box or satellite box if your cable service supplies you with a converter box or if you use a satellite system, you can use the basic connection shown in the illustration. by using this connection you can also record scram- bled channels. however, channel selection must be made with the converter box or satellite box. this means that channels cannot be changed using the tv/dvd/vcr remote control. unattended timer recording is limited to one channel at a time. preparation for use cable without converter/ descrambler box use this connection if your cable system connects directly to your tv/dvd/vcr without a converter box. by using this connection you can: 1) use the tv/dvd/vcr remote to select channels. 2) program one or more unscrambled channels for automatic timer recording. note: this tv/vcr/dvd will onl y record and view the same channel. vhf/uhf separate antennas in some areas it will be necessary to use an outdoor antenna. antenna/cable connections continued on the next page. ant. l audio out r coaxial 1 ant. in out or vhf/uhf antenna (not supplied) vhf/uhf combiner (not supplied) flat twin-lead cable uhf antenna (not supplied) vhf antenna (not supplied) from cable system 75-ohm coaxial cable (not supplied) 75-ohm coaxial cable (not sup- plied) satellite box or cable box (not supplied) from cable system or satellite dish 46. ant. in jack connect to an antenna, cable system, or satellite system. 47. power cord connect to a standard ac outlet (120v/60hz). note: remove the power cord from the hook to avoid breaking a wire before you connect to a standard ac outlet. 48. coaxial digital audio out jack connect to the digital input of an external amplifier or decoder for dvd audio only. 49. audio l/r output jack connect to the analog audio input of an external amplifier or decoder. [fig. 4] antenna/cable connection or or td853/953(p01-35).qx33 03.2.28 11:00 pm page 11 - 12 - en 1c29 to record a scrambled/unscram- bled channel 1. set the tv/dvd/vcr channel selector to the out- put channel of the cable converter box or satellite box. (ex. ch3) 2.select the channel to record from your cable converter box or satellite box. installing the batteries 1)open the battery compartment cover by pressing the cover on the remote unit in the direction of the arrow. 2)insert 2 aa penlight batteries into the battery compartment in the direction indicated by the polarity (+/-) markings. 3)replace the cover. external input mode when using an external input signal (another vcr or video camera), connect the player s audio/video out- put cables to the audio l/r in/ video in jacks of your tv/dvd/vcr. then press the channel button k or l until aux appears on the screen. aux note to catv system installer: this reminder is provided to call the catv sys- tem installer s attention to article 820-40 of the nec that provides guidelines for proper ground- ing and, in particular, specifies that the cable ground shall be connected to the grounding sys- tem of the building as close to the point of cable entry as practical. connecting to external input jacks when you watch a program recorded on an another source (vcr or video camera), use the audio/video input jacks on the front of the tv/dvd/vcr. connect the audio/video output jacks of another source to the audio l/r and video jacks of this tv/dvd/vcr. then press the channel buttons k / l until "aux" appears on the screen. note: when you connect a monaural vcr (another source) to this tv/dvd/vcr, connect the audio output jack of the monaural vcr (another source) to the audio l jack of this tv/dvd/vcr. the audio will output in both l and r channel equally. l-audio-r video headphone [another source] to the audio output jacks audio/video coaxial cable (not supplied) etc. to the video output jack [front of the tv/dvd/vcr] [fig. 5] td853/953(p01-35).qx33 03.2.28 11:00 pm page 12 - 13 - en 1c29 connecting to a stereo system ant. l audio out r coaxial 1 to right (red) and left (white) audio out jacks stereo system to analog audio input jacks notes: be sure to turn off the power to all components in the system before connecting another component. refer to the owner's manuals for your stereo system and any other components to be connected to the tv/dvd/vcr. connecting to a stereo amplifier equipped with digi- tal input jacks such as md deck or dat deck (for dvd) use an audio coaxial digital cable available at retail for the audio connections. connecting to an amplifier equipped with digital input jacks such as md deck or dat deck. notes: the audio source on a disc in a 5.1 channel dolby digital surround format cannot be recorded as digital sound by an md or dat deck. be sure to turn off the power to all components in the system before connecting another component. refer to the owner's manuals for the components to be connected to the tv/dvd/vcr. set dolby digital to off for audio output in the setup mode. playing a tv/dvd/vcr using incorrect set- tings may generate noise distortion, and may also damage the speakers. ant. l audio out r coaxial 1 amplifier equipped with digital input jacks, md deck, dat deck, etc. to coaxial digital audio input jack to digital audio out (pcm/bitstream) coaxial jack (only dvd audio out) [fig. 6] [fig. 7] td853/953(p01-35).qx33 03.2.28 11:00 pm page 13 - 14 - en 1c29 ant. l audio out r coaxial 1 front speaker (left) center speaker front speaker (right) surround speaker (left) surround speaker (right) subwoofer to digital audio out (pcm/bitstream) coaxial jack to coaxial digital audio input jack dolby digital decoder [fig. 8] connecting to a dolby digital decoder (for dvd) if using this tv/dvd/vcr to play a dvd disc in a 5.1 channel dolby digital surround format, the tv/dvd/vcr outputs a dolby digital data stream from its coaxial digital audio out jack. by hook- ing the player up to a dolby digital decoder, you can enjoy a more convincing, realistic ambience with pow- erful and high-quality surround sound as enjoyed in movie theaters. use audio coaxial digital cables available at retail for the audio connections. notes: be sure to turn off the power to all components in the system before connecting another component. refer to the owner's manuals for the components to be connected to the tv/dvd/vcr. if connected to a dolby digital decoder, set dolby digital to on for audio output in the setup mode. (see page 45 to set dolby digital to on.) unless connected to a dolby digital decoder, set dolby digital to off for audio output in the setup mode. playing a tv/dvd/vcr using incorrect settings may generate noise distortion, and may also dam- age the speakers. manufactured under license from dolby laboratories. dolby and the double-d symbol are trademarks of dolby laboratories. td853/953(p01-35).qx33 03.2.28 11:00 pm page 14 - 15 - en 1c29 set up for use you can program the tuner to scan all the channels you receive in your area. note: channel memory programming is not needed when connected to a cable box or satellite box. just select the tv/dvd/vcr channel selector to the output channel of the cable box or satellite box (ex ch3). then select the channel to be viewed on the cable box or satellite box. channel set up for the first time 1 plug in the tv/dvd/vcr power cord plug the tv/dvd/vcr power cord into a standard ac outlet. note: if some digits appear in the corner of the screen, press the power button without unplugging the power cord. 2 turn on the tv/dvd/vcr press the power button to turn on the tv/dvd/vcr. 3 select english or espa ? ol or fran ? ais select english or espa ? ol =spanish or fran ? ais =french using the enter button. [ ] indicate the selected language. 4 begin auto preset press the arrow button k or l to point to auto preset . then press the enter button. the tuner scans and memorizes all active channels in your area. notes: the tv/dvd/vcr distinguishes between standard tv channels and cable channels. if you want to play or record a video tape before presetting the tuner, you must press the setup button on the remote control. to preset the tuner again, see channel set up again on page 16. the tv/dvd/vcr may memorize tv channels as catv channels if reception conditions is poor. if this happens, try auto memo action again when reception conditions are better. 5 after scanning the tuner stops on the lowest memorized channel. if you want to recall the selected channels, you can select the desired channel directly with the remote con- trol number buttons or the channel button k or l . tv/vcr deleting (or adding) channel the channels you no longer receive or seldom watch can be deleted from the memory. (of course, you can add the deleted channel into the memory again.) 1 select channel set up press the setup button on the remote control. press the arrow button k or l to point to channel set up . then, press the enter button. 2 select add/delete ch press the arrow button k or l to point to add/delete ch . press the enter button. 3 enter the desired channel number press the arrow button k or l until your desired channel number appears. (you can also use the number buttons or the channel buttons k / l to enter it) (example: ch8) 4 delete (or add) it from (into) memory press the enter button. the channel number changes to light red. the channel is deleted from memory. to delete another channel, repeat steps [3] and [4]. if you press the enter button again, the channel is memorized again. press the return button to return to tv/vcr setup menu. 5 exit the channel setup mode press the setup button on the remote control to returns to tv mode. note: to confirm that channel(s) has been deleted or added, press the channel button k or l . tv/vcr added channel: light blue. deleted channel: light red. set up b language [english] esp fra auto preset set up language [english] esp fra b auto preset - tv/vcr setup - timer programming setting clock b channel set up user s set up v-chip set up language [english] caption [off] zero return time search index search channel set up b add / delete ch (tv) auto preset 08 add / delete tv/vcr section td853/953(p01-35).qx33 03.2.28 11:00 pm page 15 - 16 - en 1c29 channel set up again make sure ... press the power button to turn on the tv/dvd/vcr. 1 select channel set up press the setup button on the remote control. press the arrow button k or l to point to channel set up . then, press the enter button. 2 begin auto preset press the arrow button k or l to point to auto preset . then, press the enter button. the tuner scans and memorizes all the active channels in your area. 3 after scanning the tuner stops on the lowest memorized channel. tv/vcr selecting the language make sure ... press the power button to turn on the tv/dvd/vcr. note: this function effects only the language on the screen menu and not the audio source. 1 select language press the setup button on the remote control. press the arrow button k or l to point to language . 2 select english or espa ? ol or fran ? ais select english or espa ? ol = spanish or fran ? ais = french using the enter button. 3 exit the language mode press the setup button on the remote control to return to tv mode. tv/vcr note: if spanish or french is selected accidentally, 1) press the setup button on the remote control. 2) press the arrow button k or l to point to idioma [espa ? ol] or langage [fran ? ais]. 3) press the enter button to select your desired lan- guage. 4) press the setup button to exit. daylight-saving time select this feature and the tv/dvd/vcr s clock automatically will advance one hour in april, then reverse one hour in october. when daylight-saving time is on, the clock will change automatically as follows: first sunday of april : at 2 am the clock imme- diately changes to 3 am. any timer programming you have set to occur between 2 am and 3 am will not record. last sunday of october : at 2 am the clock immediately changes to 1 am. make sure ... press the power button to turn on the tv/dvd/vcr. 1 select setting clock press the setup button on the remote control. press the arrow button k or l to point to setting clock. then, press the enter button. 2 set d.s.t. (daylight-saving time) to [on] press the arrow button k or l to point to d.s.t. then, press the enter button until [on] appears. 3 exit the daylight-saving time mode press the setup button on the remote control to return to tv mode. to cancel the daylight-saving time repeat steps [1] to [2], select [off] using the enter button. tv/vcr - tv/vcr setup - timer programming setting clock b channel set up user s set up v-chip set up language [english] caption [off] zero return time search index search channel set up add / delete ch (tv) b auto preset - tv/vcr setup - timer programming setting clock channel set up user s set up v-chip set up b language [english] caption [off] zero return time search index search - tv/vcr setup - timer programming b setting clock channel set up user s set up v-chip set up language [english] caption [off] zero return time search index search setting clock auto clock [on] auto clock ch search auto clock ch [02] manual clock set b d.s.t. [on] td853/953(p01-35).qx33 03.2.28 11:00 pm page 16 - 17 - en 1c29 clock set up (auto / manual) the tv/dvd/vcr clock must be set correctly before vcr timer recording is possible. it is suggested that the clock be set manually when first setting up the tv/dvd/vcr. then, setup auto clock correction which will periodically correct the setting if necessary. note: if you cannot receive a station with time sig- nals, auto clock setting cannot be performed. use manual setting only. manual clock setting make sure ... tv/dvd/vcr power is turned on. in the example below, the clock is to be set to: date may 6th, 2003 setting time 5:40pm tv/vcr 1 select setting clock press the setup button on the remote control. press the arrow button k or l to point to setting clock . then, press the enter button. 2 select manual clock set press the arrow button k or l to point to manual clock set . then, press the enter button. 3 select the month press the arrow button k or l until your desired month appears. (example: may 05) then, press the arrow button b . 4 select the day press the arrow button k or l until your desired day appears. (example: 6th 06) then, press the arrow button b . 5 select the year press the arrow button k or l until your desired year appears. (example: 2003) then, press the arrow button b . 6 select the hour press the arrow button k or l until your desired hour appears. (example: 5, pm) then, press the arrow button b . 7 select the minute press the arrow button k or l until the desired minute appears. (example: 40) 8 start the clock press the setup button on the remote control. although seconds are not displayed, they begin counting from 00 when you press the setup button on the remote control. use this feature to synchronize the clock with the correct time. note: when unplugging the ac cord or if there is a power failure for more than 3 seconds, you may have to reset the clock. to change clock setting if you want to change the clock, 1)follow steps [1] and [2]. 2)select where you want to change using the arrow button b or s . 3)enter correct numbers using the arrow button k or l . 4)press the setup button on the remote control to start the clock. please note: if there is no local pbs station in your area or on your cable system, select auto clock and press the enter button to turn [off] this function. then you can manually adjust the clock. setting clock auto clock [on] auto clock ch search auto clock ch [02] b manual clock set d.s.t. [off] manual clock set month day year 0 5 / hour minute : manual clock set month day year 0 5 / 0 6 hour minute : manual clock set month day year 0 5 / 0 6 tue 2 0 0 3 hour minute : manual clock set month day year 0 5 / 0 6 tue 2 0 0 3 hour minute 0 5 : pm manual clock set month day year 0 5 / 0 6 tue 2 0 0 3 hour minute 0 5 : 4 0 pm 5:40 pm - tv/vcr setup - timer programming b setting clock channel set up user s set up v-chip set up language [english] caption [off] zero return time search index search td853/953(p01-35).qx33 03.2.28 11:00 pm page 17 - 18 - en 1c29 automatic clock setting make sure ... the tv/dvd/vcr is turned on. confirm the tv/dvd/vcr is receiving a rf (radio frequency) signal from either an antenna or cable system connection using the ant in jack on the rear of the tv/dvd/vcr. note: if a cable converter box is being used, make sure it is powered on. you must use the tv/dvd/vcr remote control to perform the clock setting procedure. 1 select setting clock press the setup button on the remote control. press the arrow button k or l to select setting clock . press the enter button to enter setting clock menu. 2 set auto clock to [on] press the enter button until auto clock [on] appears. 3 begin auto clock ch search press the arrow button l to select auto clock ch search . press the enter button. the tv/dvd/vcr is now searching for the station which contain the auto clock set signal. the search for a signal may take up to 20 seconds per channel. _ _ appears at the lower left of the screen when the search has ended. auto clock station- write down the number(s) that appear on the screen. these are the auto clock station(s) in your area. see item 4 below. if no number(s) appear on the tv screen, there are no stations in your area which contain the auto clock signal. auto clock setting is not possible. please use manual clock setting on page 17. press the setup button to exit the screen. note: during auto clock ch search, the picture may be distorted. this is normal. 4 enter the channel number that contains the automatic clock setting signal press the setup button on the remote control. press the arrow button k or l to select setting clock . press the enter button to enter setting clock menu. press the arrow button l to select auto clock ch . press the enter button, then press the arrow button b or s until you locate auto clock set station number. see item 3 above. press the setup button to exit the screen. 5 turn off the tv/dvd/vcr once the tv/dvd/vcr is turned off , it will period- ically check and set the correct date and time. setting clock b auto clock [on] auto clock ch search auto clock ch [02] manual clock set d.s.t. [off] setting clock auto clock [on] b auto clock ch search auto clock ch [02] manual clock set d.s.t. [off] auto clock ch search 08 10 13 _ _ setting clock auto clock [on] auto clock ch search b auto clock ch [ 45] manual clock set d.s.t. [off] - tv/vcr setup - timer programming b setting clock channel set up user s set up v-chip set up language [english] caption [off] zero return time search index search - tv/vcr setup - timer programming b setting clock channel set up user s set up v-chip set up language [english] caption [off] zero return time search index search td853/953(p01-35).qx33 03.2.28 11:00 pm page 18 - 19 - en 1c29 tv operation degaussing magnetism from nearby appliances and speakers might affect the color of the tv picture. if this happens, move this tv/vcr/dvd away from the appliance. if the color is still not correct, turn off using the power button, then turn it on again 30 minutes or so later (27 model), or unplug the power cord, then plug it in again 30 minutes or so later (19 model). tv/vcr watching a tv program 1 turn on the tv/dvd/vcr press the power button to turn on the tv/dvd/vcr. 2 select the channel number press the channel button k or l to select your desired channel number or press the number on the remote control. note for using the number button on the remote control: ? when selecting cable channels which are higher than 99, press +100 first, then, press the last two digits. (example: to select channel 125, first press +100 then press 2 and 5 ). ? you must precede single-digit channel numbers with a zero (for example: 02, 03, 04 and so on). remember: if the tv/dvd/vcr is connected to a cable box or satellite box, the tv/dvd/vcr must be on ch3 or ch4, then the channel to be viewed must be selected on the cable box or satellite box. 3 adjust sound press the volume button x x or y y to adjust the volume. notes: if you press the channel button o or p in the dvd mode, you can change the tv channels. even if you turn off the tv/dvd/vcr in the dvd mode, when you turn it on again, it will go into the tv/vcr mode. tv/vcr arrow button s arrow button b bright to decrease to increase brightness brightness contrast to decrease to increase contrast contrast color to pale to brilliant tint to purple to green sharpness to soft to clear picture control the tv/dvd/vcr s picture controls bright, contrast, color, tint and sharpness are preset to factory specifications. although they are usually the best, you may need to make some further adjustments for a natural looking image. notes: procedures must be followed within 5 seconds or the picture control mode will be cancelled. when setting the picture control, the game mode will be cancelled. make sure ... tv/dvd/vcr power must be turned on. 1 select picture control press the picture button on the remote control. 2 select item you want to adjust press the arrow button k or l until desired control is displayed. bright contrast color tint sharpness 3 adjust the picture control press the arrow button b or s to adjust to your desired level. tv/vcr if there is a power failure of any kind, the tv/vcr/dvd will retain its memory for this fea- ture. volume 20 c c c c c c c c c c c c bright p p p p p p p p p p p p p p c c p p p p p p p p p p p p p p + td853/953(p01-35).qx33 03.2.28 11:00 pm page 19 - 20 - en 1c29 closed caption system you can view specially labeled (cc) tv programs, movies, news, pre-recorded tapes with either a dia- logue caption or text display. caption mode: by choosing the caption mode, you can watch dramas, movies and news while captioning the dialogues and the contents of news. text mode: by choosing the text mode, you can watch half screen text information if you want. 1-2: you may get these captions or text information by selecting either 1 or 2 . caption 2 is used, usually for a second language if available. note: not all programs are broadcast with closed captions. your television is designed to provide error free closed captions from high quality antenna, cable and vcr signals. conversely, poor quality signals are likely to result in caption errors or no captions at all. common signal conditions which may cause captions errors are listed below: automobile ignition noise electric motor brush noise weak snowy reception on tv screen multiplex signal reception displaying picture ghosts or airplane flutter. playback of poorly recorded or worn vcr tapes. note: if the tv/dvd/vcr displays a black box on the tv screen, this means that the tv/dvd/vcr is set to the text mode. to clear screen, select [caption1], [cap- tion2] or [off]. make sure ... tv/dvd/vcr power must be turned on. tv/vcr 1 select caption press the setup button on the remote control. press the arrow button k or l to point to caption . 2 select your desired caption menu press the enter button until your desired caption menu appears. ([caption1], [caption2], [text1] or [text2]) 3 exit the caption setting mode press the setup button on the remote control to return to tv mode. to cancel the closed caption system repeat steps [1] and [2], select [off] using the enter button. press the setup button on the remote control to return to tv mode. when the closed caption mode is on the on-screen display will disappear after 5 sec- onds. it will also disappear when the mute button is pressed, and when the pause button is pressed while recording. if there is a power failure of any kind, the tv/dvd/vcr will retain its memory for this fea- ture. - tv/vcr setup - timer programming setting clock channel set up user s set up v-chip set up language [english] b caption [off] zero return time search index search - tv/vcr setup - timer programming setting clock channel set up user s set up v-chip set up language [english] b caption [caption1] zero return time search index search td853/953(p01-35).qx33 03.2.28 11:00 pm page 20 - 21 - en 1c29 5 exit the v-chip setting mode press the setup button on the remote control to exit the screen. v-chip set up make sure ... tv/dvd/vcr is turned on. 1 select v-chip set up press the setup button on the remote control. press the arrow button k or l to select v-chip set up . then, press the enter button. 2 enter access code use the number buttons on the remote control to enter the access code. for the first time set-up or in the event the tv/dvd/vcr has lost power, enter the default code of the numbers: 0000. 3 select tv rating press the arrow button k or l to select tv rating . then, press the enter button. 4 blocking tv programs press the arrow button k or l to select tv rating that you wish to block. press the enter button to turn it [block]. when you select the rating category and turn it [block], the higher rating will turn [block] automatically. also, the lower rating will turn [view] automatically. when you turn tv-y to [view], then all ratings will turn to [view] automatically. tv/vcr access code _ _ _ _ v-chip set up - tv/vcr setup - timer programming setting clock channel set up user s set up b v-chip set up language [english] caption [off] zero return time search index search v-chip set up b tv rating mpaa rating change code b tv y [view] tv y7 ( ) [view] tv g [view] tv pg ( ) [view] tv 14 ( ) [view] tv ma ( ) [view] selection rating category explanations tv-y appropriate for all children tv-y7 appropriate for children seven and older tv-g general audience tv-pg parental guidance suggested. tv-14 unsuitable for children under 14 tv-ma mature audience only v-chip set up sub ratings when you select the ratings of tv-y7,tv-pg,tv-14 or tv-ma you will have the option of selecting sub rating categories. 1 select v-chip set up press the setup button on the remote control. press the arrow button k or l to select v-chip set up . then, press the enter button. 2 enter access code use the number buttons on the remote control to enter the access code. (default code is 0000.) 3 select tv rating press the arrow button k or l to select tv rating . then, press the enter button. 4 selecting sub-ratings press the arrow button l to select the sub-rating you wish to block. then, press the enter button twice. when you select [tv-y7]: press the arrow button l or k to select fv (fantasy violence). then, press the enter button to select [block] or [view]. when you select [tv-pg], [tv- 14] or [tv-ma]: press the arrow button l or k to select d (suggestive dialog), l (coarse language), s (sexual situation), or v (violence). then, press the enter button to select [block] or [view]. note: when you select [tv-ma], d does not appear on the tv screen. the sub-ratings which set to [block] appears next to the rat- ing category in the tv rating menu. 5 exit the v-chip setting mode press the setup button on the remote control to enter the setting and exit the screen. v-chip set up b tv rating mpaa rating change code tv y7 [block] b fv [block] tv pg [block] b d [block] l [block] s [block] v [block] b tv y [view] tv y7 ( ) [view] tv g [view] tv pg (dlsv ) [block] tv 14 (dlsv ) [block] tv ma ( lsv ) [block] access code _ _ _ _ - tv/vcr setup - timer programming setting clock channel set up user s set up b v-chip set up language [english] caption [off] zero return time search index search td853/953(p01-35).qx33 03.2.28 11:00 pm page 21 - 22 - en 1c29 changing v-chip blocked pro- gramming note: to change the rating, the tv must be turned to a station that is not protected. if the (protected) appears on the screen, please change the channel to a station that is not protected. 1)follow steps [1] and [2]. 2)press the arrow button k or l to select "tv rat- ing". then, press the enter button. select a tv rating to be unblocked by pressing the arrow but- ton k or l . then press the enter button to unblock the rating. 3)press the setup button on the remote control to exit the screen. mpaa rating set up 1 select v-chip set up press the setup button on the remote control. press the arrow button k or l to select v-chip set up . then, press the enter button. 2 enter access code use the number buttons on the remote control to enter the access code. 3 select mpaa rating press the arrow button k or l to point to mpaa rating . then, press the enter button. 4 select your desired item press the arrow button k or l to point to your desired item. then, press the enter button to select [block] or [view]. when you select the rating category and turn it [block], the higher rating will turn [block] automatically. also, the lower rating will turn [view] automatically. when you turn g to [view], then all ratings will turn to [view] automatically. selection rating category explanations g general audience pg parental guidance suggested. pg-13 unsuitable for children under 13 r restricted; under 17 requires accompa- nying parent or adult guardian nc-17 no one under 17 admitted x mature audience only v-chip set up tv rating b mpaa rating change code g [view] pg [view] pg 13 [view] b r [block] nc 17 [block] x [block] access code _ _ _ _ 5 exit the v-chip setting mode press the setup button on the remote control to exit the screen. change access code to change access code, follow the steps. 1 select v-chip set up press the setup button on the remote control. press the arrow button k or l to select v-chip set up . then, press the enter button. 2 enter access code use the number buttons on the remote control to enter the access code. the default code is 0000. 3 select change code press the arrow button k or l to select "change code". then, press the enter button. 4 enter new code use the number buttons to enter your desired access code in the new code space. then enter the same code in the confirm code space. v-chip set up screen appear on the screen. if you enter wrong code, repeat step 4, making sure you enter the same new code exactly in the confirm code space. 5 exit the v-chip setting mode press the setup button on the remote control to exit the screen. note: if you unplug the power code or power failure occurs, the changed access code will be lost and will return to default (0000). change your access code again as necessary. access code _ _ _ _ new code x x x x confirm code _ _ _ _ v-chip set up tv rating mpaa rating b change code - tv/vcr setup - timer programming setting clock channel set up user s set up b v-chip set up language [english] caption [off] zero return time search index search td853/953(p01-35).qx33 03.2.28 11:00 pm page 22 - 23 - en 1c29 mts(multi-channel television sound)system you can record or listen to a program in mts stereo. checking the selected mts mode when you play a vhs tape, or receive a broadcast on the tv/dvd/vcr tuner channel you are watching, the status shown below will appear when you press the display button on the remote control. play b 12:00am hifi ch 123 stereo/sap sp count 0:00:00 1] when a program is broadcast in stereo, stereo appears on the tv screen. 2] when a program is broadcast in second audio, sap appears on the tv screen. 3] when a program broadcast both in stereo and sec- ond audio, stereo and sap appear on the tv screen. note: although a program may be broadcast in both stereo and second audio, you cannot record in both stereo and second audio at the same time. 4] while the tv/dvd/vcr is set in hifi stereo mode and playback mode. hifi appears on the tv screen. while the tv/dvd/vcr is set in monaural(mono) mode, hifi disappears from the tv screen. note: if you play non-hifi tapes while the tv/dvd/vcr is set in hifi, hifi will dis- appear from the tv screen and the tv/dvd/vcr will play automatically in monaural. mts recording/monitor mode type of broadcast display on stereo/sap hi-fi audio track(2-channel) normal audio the tv screen selection l-channel r-channel track regular -none- -invalid- mono mono mono (monaural audio) stereo broadcast stereo -invalid- l r l+r bilingual broadcast sap stereo* main audio main audio main audio program program program sap* sub audio sub audio sub audio program program program stereo & bilingual stereo stereo* l r l+r broadcast sap sap* sub audio sub audio sub audio program program program * you must select the recording mode in tv audio [stereo] or [sap] when you record a broadcast. 2] 3] 1] 4] sap second audio program, which means your program, can also be received in a second language or sometimes a radio station. hifi high fidelity which produces better sound than standard stereo tv/dvd/vcrs. tv/vcr tv/vcr td853/953(p01-35).qx33 03.2.28 11:00 pm page 23 - 24 - en 1c29 selecting the mts system make sure ... tv/dvd/vcr power must be turned on. to select hifi mode 1 select user s set up press the setup button on the remote control. press the arrow button k or l to point to user s set up . then, press the enter button. 2 select vcr audio press the arrow button k or l to point to vcr audio . 3 select [hifi] press the enter button until [hifi] appears. 4 to return to tv mode press the setup button on the remote control to return to tv mode. notes: normally, hifi should be selected for playback with hifi sound. when you play non-hifi tapes, the tv/dvd/vcr will play automatically in the monaural mode. the tv/dvd/vcr records automatically mts broadcasts in hifi stereo sound unless you select sap mode recording before you begin recording. to select stereo, sap, or mono 1 select user s set up press the setup button on the remote control. press the arrow button k or l to point to user s set up . 2 select tv audio press the arrow button k or l to point to tv audio . 3 select [stereo], [sap], or [mono] press the enter button until [stereo], [sap], or [mono] appears. 4 to return to tv mode press the setup button on the remote control to return to tv mode. notes: you must select the recording mode,either tv audio [stereo] or [sap] when you record a broadcast. refer to mts recording/monitor mode . if you select second audio when second audio is not available, the tv/dvd/vcr will record normal audio. the tv/dvd/vcr records automatically mts broadcasts in hifi stereo sound unless you select sap mode recording before you begin recording. - tv/vcr setup - timer programming setting clock channel set up b user s set up v-chip set up language [english] caption [off] zero return time search index search - tv/vcr setup - timer programming setting clock channel set up b user s set up v-chip set up language [english] caption [off] zero return time search index search user s set up rental [off] repeat play [off] auto return [off] b vcr audio [hifi] tv audio [stereo] user s set up rental [off] repeat play [off] auto return [off] vcr audio [hifi] b tv audio [stereo] user s set up rental [off] repeat play [off] auto return [off] b vcr audio [hifi] tv audio [stereo] to select mono mode you can change the selection to mono if you want to listen to hifi tapes in normal audio play- back. 1) press the setup button on the remote control. press the arrow button k or l to point to user s set up .then, press the enter button. 2) press the arrow button k or l to point to vcr audio . 3) press the enter button until [mono] appears. 4) press the setup button on the remote control to return to tv mode. tv/vcr td853/953(p01-35).qx33 03.2.28 11:00 pm page 24 - 25 - en 1c29 video cassette this tv/dvd/vcr will operate with any cassette that has the mark. for best results, we recommend the use of high-quality tapes. do not use poor quality or damaged tapes. removing a cassette 1)in the stop mode, press the eject button on the remote control or press the stop/eject button on the tv/dvd/vcr. the cassette will eject. 2)pull the cassette out of the cassette compartment. 3)store the cassette in its case as shown. note: in dvd mode, whether the cassette is with tab or without tab you insert, it doesn t start playing until you press the play button. in tv/vcr mode, if th cassette without tab is inserted, playback will automatically start. precautions avoid moisture. moisture condensation may occur on the tape if it is moved from a cold place to a warm place or visa versa. before using a tape with these conditions, to avoid damage of the tape and your tv/dvd/vcr, wait until the tape has warmed to room temperature and the moisture has evaporated. avoid extreme heat, high humidity and magnetic fields. do not tamper with the cassette mechanism. do not touch the tape with your fingers. inserting a cassette insert the cassette in the direction as shown. push in gently, but continuously, on the center-back of the cassette until it is drawn into the tv/dvd/vcr. the tv/dvd/vcr will automatically turn on. two different tape speeds before recording, select the tape speed from : sp mode (standard play) or slp mode (super long play). the table below shows the maximum recording/play- back time using t60, t120 or t160 tapes in each mode. note: you can play back a tape recorded in lp mode (long play). tape speed recording/playback time type of tape t60 t120 t160 sp mode 1 hour 2 hours 2-2/3 hours slp mode 3 hours 6 hours 8 hours erase prevention you can prevent accidental erasing of recording by breaking off the tab on the back edge of the cassette. if you decide to record on the tape again, cover the hole with plastic tape. correct window wrong ta b transparent tape td853/953(p01-35).qx33 03.2.28 11:00 pm page 25 - 26 - en 1c29 playback normal playback make sure ... tv/dvd/vcr power must be turned on. 1 insert a prerecorded tape if the erase-protection tab has been removed, the tv/dvd/vcr will start playback automatically. 2 to begin playback press the play button. 3 to stop playback press the stop button when play- back is completed. notes: if you press the play button (of the tv/vcr side) in the dvd mode, you can start the vcr playback. if you press the select button in the vcr play- back, it will stop and the mode will change to the dvd mode. in addition, the same function oper- ates with the dvd side play button or the open/close button. tv/vcr tracking adjustment tracking adjustment will be set automatically (digital tracking function) when you start play- back. however when playing pre-recorded tapes or tapes recorded on units other than your own, noise lines (black and white streaks) may appear on the play- back picture. if this occurs, you can adjust the tracking control manually by pressing the chan- nel button k or l until the streaks disappear. to return to the dtr function, stop the tape once and start playback again. you can reduce the noise lines by pressing the channel button k or l in slow mode, too. tracking adjustment in slow mode will not be set automatically. tv/vcr picture search this feature is very useful in finding or skipping over a particular scene on a tape. in this mode, the sound will be muted. 1)you may view a video tape at a high speed in either a forward or reverse direction by pressing the f.fwd or rew button during playback. (in the sp / lp / slp modes) note: if you press the f.fwd or rew button on the front panel in the dvd mode, the vcr forward or reverse will start. please press the stop / eject button once to stop it, twice to eject it. 2) press it again and the tv/dvd/vcr will now search in super high speed. (in the lp / slp modes only) note: tapes recorded in the sp or lp mode will dis- play a noise bar on the tv screen and the picture may revert to black and white. this is normal. 3)press the play button to return to normal speed. tv/vcr still picture you can view a still picture on the tv screen during playback (the still mode). press the pause button during playback. only tapes recorded in the slp mode will show the least amount of lines.press the play button to return to playback. notes: you can advance the picture one frame at a time by pressing the pause button during the still mode. if it is left in the pause mode for more than five minutes, the tv/dvd/vcr will automatically switch to the stop mode. tv/vcr vertical hold control in the pause/still mode only, when the picture begins to vibrate vertically, stabilize the picture by pressing the channel button k or l . note: if there are video noise lines on the screen, see tracking adjustment section. tv/vcr slow motion during pause, press the fwd button to reduce the playback speed. the tv/dvd/vcr mutes the sound during slow motion. press the play button to return to normal playback. note: if it is left in the slow mode for more than five minutes, the tv/dvd/vcr will automatically go into the stop mode. tv/vcr play b stop td853/953(p01-35).qx33 03.2.28 11:00 pm page 26 - 27 - en 1c29 special playback this function enables you to improve the picture quality when playing back worn cassettes such as rented tapes. 1 select user s set up press the setup button on the remote control. press the arrow button k or l to point to user s set up . then, press the enter button. 2 set rental to [on] press the arrow button k or l to point to rental . press the enter button until [on] appears. 3 exit the rental setting press the setup button on the remote control to return to the tv mode. 4 start playback press the play button to start playback. rental play b appears. once you select the rental mode, it stays in effect even after you turn off the tv/dvd/vcr. to cancel the rental mode repeat steps [1] and [2], select [off] using the enter button on the remote control. press the setup button on the remote control to return to tv mode. if there is a power failure of any kind, the tv/vcr/dvd will retain its memory for this feature. tv/vcr make sure ... tv/dvd/vcr power must be turned on. insert a prerecorded tape. rental playback the tv/dvd/vcr has the auto repeat function that allows you to repeat a tape indefinitely without touching the play button. all repeat: repeat playback from the beginning to the end of the tape. blank repeat : repeat playback from the begin- ning to a blank part, which is blank for more than 10 seconds. 1 select user s set up press the setup button on the remote control. press the arrow button k or l to point to user s set up . then, press the enter button. 2 select all or blank press the arrow button k or l to point to repeat play . press the enter button repeatedly until your desired selection [all] or [blank] appears. 3 exit the repeat play setting press the setup button on the remote control to return to the tv mode. 4 start playback press the play button to start the repeat play. repeat play b appears. once you select the repeat play mode, it stays in effect even after you turn off the tv/dvd/vcr. if the rental mode is set [on], the rental play b display has priority. to cancel the repeat play mode repeat steps [1] and [2], select [off] using the enter button on the remote control. press the setup button on the remote control to return to tv mode. if there is a power failure of any kind, the tv/dvd/vcr will retain its memory for this fea- ture. tv/vcr auto repeat playback - tv/vcr setup - timer programming setting clock channel set up b user s set up v-chip set up language [english] caption [off] zero return time search index search user s set up b rental [on] repeat play [off] auto return [off] vcr audio [hifi] tv audio [stereo] - tv/vcr setup - timer programming setting clock channel set up b user s set up v-chip set up language [english] caption [off] zero return time search index search user s set up rental [off] b repeat play [all] auto return [off] vcr audio [hifi] tv audio [stereo] td853/953(p01-35).qx33 03.2.28 11:00 pm page 27 - 28 - en 1c29 search make sure ... tv/dvd/vcr power must be turned on. insert a tape. this function allows you to search easily a beginning point that you want to review by rewinding or fast forwarding. note: zero return will not work on a blank tape or a blank portion of a tape. 1 stop a tape at your desired point rewind or fast forward the tape to the beginning point at which you want to review. 2 reset the counter to 0:00:00 press the c.reset button repeatedly. 3 begin recording or playback press the record or play button. press the stop button when recording or playback is completed. 4 to activate zero return mode press the setup button on the remote control. press the arrow button k or l to point to zero return . then, press the enter button. the counter will appear on the tv screen. the tape will automatically stop when the counter returns to 0:00:00. tv/vcr zero return the time search function makes it possible to quick- ly advance the tape to your desired position simply by entering the exact amount of playback time you want to skip. notes: time search can be set up to a maximum of 9 hours 50 minutes (9:50) by 10 minutes at a time. tv/vcr time search this function will not operate in recording mode. this function is not operative when a cassette tape is not inserted in the tv/dvd/vcr. in the example below: to watch a program after 2 hour 50 minutes from the present position, in either direction. 1 insert a tape. 2 select time search mode press the setup button on the remote control. press the arrow button k or l to point to time search . then, press the enter button. 3 enter your desired time press the arrow button k or l until your desired time appears. (example: 2:50 stands for 2 hours 50 minutes) if you wish to cancel the time search at this point, press the setup button on the remote control. 4 begin time search by pressing the arrow button s or b , the tv/dvd/vcr will rewind or fast forward to the specified point. the time counts down as the searching progresses. when 0:00 is reached, the tape will start playback automatically. to cancel the time search at this point press the stop/eject button on the tv/dvd/vcr or the stop button on the remote control. this will delete the selected time. - tv/vcr setup - timer programming setting clock channel set up user s set up v-chip set up language [english] caption [off] b zero return time search index search - tv/vcr setup - timer programming setting clock channel set up user s set up v-chip set up language [english] caption [off] zero return b time search index search time search 2 : 50 td853/953(p01-35).qx33 03.2.28 11:00 pm page 28 - 29 - en 1c29 index search this feature provides a method of indexing the start- ing point so that it can be easily returned to in either fast forward or rewind mode. the index mark will be made automatically when the rec button is pressed. it will also be marked at the starting point of timer recording and otr. the index mark will not be recorded if the pause button is pressed and released during recording. the time gap between making the index marks on the tape should be greater than 1 minute for sp recording, 2 minutes for lp recording and 3 min- utes for slp recording. in some cases, the index mark at the beginning of video tape cannot be detected. example: you are watching program number 4 and want to fast forward to program number 7. you must skip three programs. tv/vcr 1 select index search press the setup button on the remote control. press the arrow button k or l to point to index search . then, press the enter button. 2 enter your desired number press the arrow button k or l until the number of programs that you want to skip appears. (example: 03 for 3 programs) the index search mode will be canceled if the procedures are not activated in 30 seconds. 3 begin index search press the arrow button s or b . the tv/dvd/vcr begins rewinding or fast forwarding to the beginning of desired program. note: every time an index signal is skipped, the number in the program indicator decreases by one. 4 after index search when the preset program is reached, the tv/dvd/vcr will start playback automatically. a video cassette must be inserted in the tv/dvd/vcr for this function to work. the number of index searches can be set up to 20. this function will not operate in the recording mode. when you want to cancel the index search while in progress, press the stop button. pro.1 pro.2 pro.3 pro.4 pro.5 pro.6 pro.7 4321123 end of tape beginning of tape current playback program index mark - tv/vcr setup - timer programming setting clock channel set up user s set up v-chip set up language [english] caption [off] zero return time search b index search index search 0 3 special features real time tape counter this shows the elapsed recording or playback time in hours, minutes, and seconds. (the displayed time will not change on a blank tape or blank portions on the tape.)the indication will appear when the tape has rewound further than 0:00:00 on the tape counter. tv/vcr auto rewind-eject when the end of a tape is reached during record- ing, playback, or fast-forward, the tape will auto- matically rewind to the beginning. after rewinding finishes, the tv/dvd/vcr will eject the tape and turn itself to off. this function is operative when repeat play is set to the [off] position. the tape will not auto-rewind during timer record- ing or one touch recording. tv/vcr td853/953(p01-35).qx33 03.2.28 11:00 pm page 29 - 30 - en 1c29 recording make sure ... tv/dvd/vcr power must be turned on. insert a cassette tape with its erase prevention tab in place. (if necessary, rewind or fast forward the tape to the point at which you want to begin recording.) notes: this tv/vcr/dvd will onl y record and view the same channel. this tv/vcr/dvd cannot record the contents from the built-in dvd. you can onl y watch the same tv program that is being recorded. 1 select the channel to be recorded press the number buttons on the remote control or the channel button k or l . remember: if the tv/dvd/vcr is connected to a cable box or satellite box, the tv/dvd/vcr must be on ch3 or ch4, then the channel to be recorded must be selected on the cable box or satellite box. 2 select the tape speed press the speed button to select the desired tape speed (sp/ slp). 3 begin recording press the record button. 4 stop recording press the stop button when recording is completed. tv/vcr normal recording press the pause button to tem- porarily stop recording. press the pause or record but- ton to resume recording. notes: after five minutes, the tv/dvd/vcr will auto- matically switch to the recording mode to prevent tape damage. if closed caption (on) is selected, the on- screen display will appear for 5 seconds, then dis- appear. tv/vcr skipping unwanted scenes during recording ch 10 sp rec sp pause sp td853/953(p01-35).qx33 03.2.28 11:00 pm page 30 - 31 - en 1c29 this function enables you to set a recording length simply by pressing the rec/otr button on the tv/dvd/vcr. make sure ... tv/dvd/vcr power must be turned on. insert a cassette tape with its erase prevention tab in place. (if necessary, rewind or fast forward the tape to the point at which you want to begin recording.) notes: this function cannot be done from the remote control. recording starts immediately when the rec/otr button is pressed. when the rec/otr button is pressed 18 times, the tv/dvd/vcr returns to the normal recording mode. to stop the otr operation, press the stop button on the tv/dvd/vcr or on the remote control. to show the remaining time, press the display button on the remote control so that otr appears on the tv screen. (it will show up momen- tarily then disappear.) recording stops when 0:00 is reached. please note that in the slp mode maximum record- ing time, assuming the tape is started at the begin- ning, is 8 hours using t-160 (or 6 hours using t-120). if the tape runs out before the end time, the tv/dvd/vcr will switch to the stop mode immediately, ejects the tape and turns itself off. if you press the power button during otr, the tv/dvd/vcr continues recording until the select- ed length is reached. 1 select the channel to be recorded press the number buttons on the remote control or the channel button k or l . remember: if the tv/dvd/vcr is connected to a cable box or satellite box, the tv/dvd/vcr must be on ch3 or ch4, then the channel to be recorded is selected on the cable box or satellite box. 2 select the tape speed press the speed button to select the desired tape speed (sp/ slp). 3 begin otr press the rec/otr button on the tv/dvd/vcr as many times as needed. the recording length will be determined by the number of times you press the rec/otr button. each additional push will increase the recording time by 30 minutes. it is set up to 8 hours. tv/vcr otr (one touch recording) push(es) display recording length 1 push (normal recording) 2 pushes 0:30 30 minutes 3 pushes 1:00 60 minutes 17 pushes 8:00 480 minutes you can make copies of video tapes made by friends or relatives for your enjoyment. you can not copy a dvd to a videotape. connect your tv/dvd/vcr and a source (playing) vcr using the following diagram. 1)insert a pre-recorded video cassette into the source (playing) vcr or camcorder. 2)insert a blank video cassette, or one you want to record over, into the tv/dvd/vcr s cassette compartment. 3)press the speed button on remote control for the tv/dvd/vcr to select the desired recording speed (sp/slp). 4)press the channel button k or l on the tv/dvd/vcr until aux appears on the screen. 5)press the record button on the tv/dvd/vcr. 6)begin playback of the tape in the source (playing) vcr or camcorder. note: for best results during copying, use the tv/dvd/vcr s front panel controls whenever pos- sible. the remote control might affect the source (playing) vcr s playback operation. tv/vcr copying a video cassette (requires a vcr or camcorder) warning: unauthorized recordings of copyrighted video tapes may be an infringement of copyright laws. r l audio video headphone ec/otr c stop f.fwd g b play h rew a eject video in out audio in out l r [fig.8] [ex: source (playing) vcr or camcorder] audio/video adapter cable (not supplied) [the tv/dvd/vcr] otr(2 : 30) sp td853/953(p01-35).qx33 03.2.28 11:00 pm page 31 - 32 - en 1c29 timer you may set the tv/dvd/vcr to start and end a recording while you are away. you can set 8 pro- grams to record on specific days, daily or weekly within a 1 year period. in the example below, the timer is being set to record: date: july 4th, 2003 setting time: from 7:30pm to 8:50pm channel: ch61 tape speed: sp make sure ... if a cable box or satellite box is connected with the tv/dvd/vcr you will be limited to record only one channel. and the channel selector on the tv/dvd/vcr must be selected to the output channel of the boxes ch 3 or ch 4 and then the actual chan- nel to be recorded must be selected on the boxes. clock must be set to the correct time and date before setting the timer. tv/dvd/vcr power must be turn on to program it. insert a cassette tape with its erase prevention tab in place. (if necessary, rewind or fast forward the tape to the point at which you want to begin recording.) the channel you want to record is properly set in advance. (see page 16.) avoid over lap of programs ... there is a chance that a program will not be record- ed. when programs overlap; the program with an earlier start has priority. once the earliest program finishes, the overlapping programs will begin recording in sequence. the illustration below demonstrates the sequence of recordings. program 1 10:00am - 11:00am program 2 9:00am - 10:00am program 3 9:30am - 12:00pm tv/vcr automatic timer recording 9:00am 10:00am 12:00pm program 1 10:00am-11:00am program 2 9:00am-10:00am program 3 9:30am-12:00pm 11:00am recording sequence *recording period is shaded 1 select timer programming press the setup button on the remote control. confirm timer program- ming is pointed by pressing the arrow button k . and press the enter button. if you have not yet set the clock, manual clock set appears. if so, follow stops [3] to [8] on page 17. then set the timer recording. 2 select your desired program position (1~8) press the arrow button k or l to select the desired program position. then, press the arrow button b . 3 set the channel number press the arrow button k or l until the desired channel number appears. (example: ch61) then, press the arrow button b . remember: if the tv/dvd/vcr is connected to a cable box or satellite box, the tv/dvd/vcr must be on ch3 or ch4, then the channel to be recorded is selected on the cable box or satellite box. 4 select once, every day or weekly recording for once recording : press the arrow button k (up) until the desired date appears. (example: 7/04 for july 4th). then, press the arrow button b . for every day recording : to record a tv program at the same time on the same channel every day. (example: monday through sunday) press the arrow button l (down) until evry day appears. then, press the arrow button b . for weekly recording : to record a tv program at the same time on the same channel every week. (example: every monday) press the arrow button l (down) until evry and your desired day of the week appear together. then, press the arrow button b . - tv/vcr setup - b timer programming setting clock channel set up user s set up v-chip set up language [english] caption [off] zero return time search index search timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 evry day -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 7/04 fri -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 evry mon -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - td853/953(p01-35).qx33 03.2.28 11:00 pm page 32 - 33 - en 1c29 to shift the time schedule of an automatic timer recording. 1)press the power button. 2)repeat step [1] on page 32. 3)press the record button and select the desired program using the arrow button k or l . 4)press the record button again. each additional push will shift forward the begin/end time for recording by 10 minutes. when the recording is already in progress, each additional push will shift forward the end time only. if you want to cancel while setting, press the pause but- ton on the remote control. the recording time returns to the original time. note: when you shift forward the time schedule during recording, the recording speed will automati- cally be set to the slp mode. 5)press the enter or return button to exit the setting menu. then press the setup button on the remote control to return to original mode. to correct a program while setting a program; press the arrow button s to go back one step and enter the correct num- bers using the arrow button k or l . after setting a program; 1)press the power button. 2)repeat steps [1] - [2] on page 32. 3)press the arrow button b (or press the arrow button s to go back one step) until the part you want to correct begins flashing, then make the changes pressing the arrow button k or l . 4)press the power button to set automatic timer recording. to cancel an automatic timer recording after setting a program; 1)press the power button. 2)repeat steps [1] ~ [2] on page 32 and select a program you want to cancel. 3)press the c.reset button. 4)press the setup button on the remote control to return to tv mode. while recording is in progress; 1)press the power button. 2)press the stop/eject button on the tv/dvd/vcr . tv/vcr 5 set beginning hour press the arrow button k or l until the desired hour appears. (example: 7, pm for 7 :30 pm ) then, press the arrow button b . 6 set beginning minute press the arrow button k or l until the desired minute appears. (example: 30 for 7: 30 pm) then, press the arrow button b . 7 set end hour press the arrow button k or l until the desired hour appears. (example: 8, pm for 8 :50 pm ) then, press the arrow button b . 8 set end minute press the arrow button k or l until the desired minute appears. (example: 50 for 8: 50 pm) then, press the arrow button b . 9 set the tape speed press the arrow button k or l until the desired tape speed appears. (example: sp) 10 finish setting the program press the enter or return button. the program is now completed. to set another program, repeat steps [2] to [10]. press the setup button on the remote control to return to original mode. 11 set the timer press the power button to set automatic timer recording. the recording indicator lights up. you must turn off the tv/dvd/vcr to activate automatic timer recording. if power is not turned off and you continue watch- ing tv, timer rec standby starts flashing on the tv screen 2 minutes before the programmed start time. timer program extension timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 7/04 fri 7:12 p m -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 7/04 fri 7:30 p m -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 7/04 fri 7:30 p m 8:30 p m - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 7/04 fri 7:30 p m 8:50 p m - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - timer programming ch date begin end - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - b 61 7/04 fri 7:30 p m 8:50 p m sp - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - - - -/- - - - - -:- - -:- - - - td853/953(p01-35).qx33 03.2.28 11:00 pm page 33 - 34 - en 1c29 to check the begin/end time 1)press the power button so that the recording indicator goes off. 2)press the setup button on the remote control. 3)confirm timer programming is pointed. 4)press the enter button. the details of programs appear on the tv screen. 5)press the setup button on the remote control to return to tv mode. hints for automatic timer recording make sure the channel you want to record is prop- erly set in advance. it is not necessary to press the record button for timer recording. recording begins automatically at the start time. if you are recording using a timer mode, you may not operate the tv/vcr/dvd manually. the erase-prevention tab on the cassette must be in place (or you must put tape over the hole). if the erase-prevention tab is removed, the cassette will be ejected when the power button is pressed to off. if the tape runs out before the end time, the tv/dvd/vcr will switch to the stop mode immediately, and the tape will be ejected. tv/vcr auto return with this feature, after timer recording is finished, the beginning of the recorded program(s) can be searched for automatically. 1 select user s set up press the setup button on the remote control. press the arrow button k or l to point to user s set up . then, press the enter button. 2 set auto return to [on] press the arrow button k or l to point to auto return . press the enter button until [on] appears. tv/vcr 3 auto return will begin when all the timer recordings are completed, the tv/dvd/vcr will rewind to the beginning of the recorded program(s). note: if you press the power button while tape is rewinding, the auto return will stop. 4 watch the recorded program press the play button. to cancel the auto return mode repeat steps [1] and [2], select [off] using the enter button. if there is a power failure of any kind, the tv/vcr/dvd will retain its memory for this fea- ture. - tv/vcr setup - timer programming setting clock channel set up b user s set up v-chip set up language [english] caption [off] zero return time search index search user s set up rental [off] repeat play [off] b auto return [on] vcr audio [hifi] tv audio [stereo] sleep timer the sleep timer function turns off the tv/dvd/vcr without using the power button after a desired period of time. note: this function does not operate during recording mode. tv/vcr 1 select sleep timer press the sleep button on the remote control until sleep timer appears. 2 set sleep time press the sleep button until your desired sleep time appears. each additional push will increase the time by 30 minutes up to 120 minutes. after 5 seconds, exit the sleep timer setting. to cancel the sleep timer press the sleep button on the remote control until sleep timer appears. press the sleep button until sleep 0 minutes appears. sleep 120 minutes td853/953(p01-35).qx33 03.2.28 11:00 pm page 34 - 35 - en 1c29 on screen display to check the counter, clock and channel number on the tv screen, press the display button on the remote control. each time you press the display button on the remote control, the tv screen will change as follows: when the closed caption mode is off: counter mode: after 5 seconds, only the counter remains. to clear it, press the display button. clock mode: after 5 seconds, only the clock and the channel number remain. to clear them, press the display button. when the closed caption mode is on: the on screen display disappear after 5 seconds. this is true even if the mute button is pressed, or the pause button is pressed while recording. off mode clock/counter mode stop 5:40 pm ch2 sp count 0:12:34 stop stop sp sp count 0:12:34 count 0:12:34 5:40pm ch2 5:40pm ch2 counter remains clock & channel remains after 5 seconds after 5 seconds off mode counter mode clock mode cable channel designations if you subscribe to cable tv, the channels are displayed as 1-125. cable companies often designate channels with letters or letter-number combinations. please check with your local cable company. the following is a chart of common cable channel designations. tv display tv display tv display tv display tv display tv display tv display tv display catv channel tv display w+80 w+81 w+82 w+83 w+84 w+65 w+66 w+67 w+68 w+69 w+70 w+71 w+72 w+73 w+74 w+75 w+76 w+77 w+78 w+79 w+55 w+56 w+57 w+58 a-4 a-3 a-2 a-1 w+59 w+60 w+61 w+62 w+63 w+64 w+40 w+41 w+42 w+43 w+44 w+45 w+46 w+47 w+48 w+49 w+50 w+51 w+52 w+53 w+54 w+25 w+26 w+27 w+28 w+29 w+30 w+31 w+32 w+33 w+34 w+35 w+36 w+37 w+38 w+39 w+10 w+11 w+12 w+13 w+14 w+15 w+16 w+17 w+18 w+19 w+20 w+21 w+22 w+23 w+24 a-5 r s t u v w w+1 w+2 w+3 w+4 w+5 w+6 w+7 w+8 w+9 cdefgh i jklmnopq 5a 2 3 4 5 6 7 8 9 10 11 12 13 a b 123456789101112131415 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 catv channel catv channel catv channel catv channel catv channel catv channel catv channel catv channel td853/953(p01-35).qx33 03.2.28 11:00 pm page 35 36 en 01a11 dvd section about the discs disc types the following discs can be played back on this tv/dvd/vcr. ? dvd video ? dvd-r/rw* ? dvd+r/rw* ? audio cd ? cd-r/rw* ? mp3* * depending on the types or the writing method of the medium some discs can not be played. some dvd-r/rw, dvd+r/rw, or cd-r/rw discs made on personal computers, or on dvd recorders may not be played back properly due to the factors such as scratches, dirt or special properties of the disc. discs made on personal computers may not be played back properly due to the different environment or the settings of the application you use. we recommend always to use the standardized, rightly formatted discs. (please contact the sales agency for more detail). this player conforms to the ntsc color system. you can- not play discs recorded in other color systems such as pal or secam. ? some discs include region codes as shown below. ? the number inside the symbol refers to a region of the world, and a disc encoded in a specific region format can only be played back on tv/dvd/vcr with the same region code. the following discs cannot be played back on this tv/dvd/vcr. ? dvd with region codes other than 1 or all. ? dvd-rom ? dvd-ram (never play back, otherwise malfunc- tion may result.) ? cd-rom ? vsd ? cdv (only plays back the audio part.) ? cd-g (only plays back the sound.) ? cd-i (ne ver play back, otherwise malfunction may result.) ? sacd ? photo cd (never play back, otherwise malfunc- tion may result.) ? video cd (never play back, otherwise malfunc- tion may result.) any other discs without compatibility indications. playable discs [ dvd ] data on a dvd is divided into sections called "titles", and then into subsections called "chapters", each of which is given a title or chapter number. playback conditions are preset on some dvd video discs, and these playback con- ditions take priority over user operations on this player. if a function you selected does not run as desired, refer to the manual accompanying the disc. example title 1 title 2 chapter 1 chapter 2 chapter 1 chapter 2 chapter 3 chapter 4 [ audio cd ] data on an audio cd is divided into sections called tracks , each of which is given a track number. example track 1 track 2 track 3 track 4 track 5 track 6 [ mp3 ] data on an mp3 is divided into sections called "groups", and then into subsections called "tracks", each of which is given a group or track number. example group 1 group 2 track 1 track 2 track 1 track 2 track 3 track 4 td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 36 37 en 01a11 playing a disc basic playback getting started ? turn on the power of amplifier and any other com- ponents, if necessary. 1 press the power button. ? the power will turn on. 2 press the open/close button to open disc loading tray. 3 place the chosen disc in the tray, with the label facing up. cd dvd-v 4 press the play button. ? the tray will close automatically, and playback will then start from the first chapter or track of the disc. if the playback does not start automatically, press the play button. ? when you playback the dvd which a title menu is recorded, it may appear on the screen. in this case, refer to title menu . 5 press the stop button to stop playback. notes ? when the dvd mode has been switched to the tv/vcr mode, the dvd mode shuts down first and then tv picture and sound appears in about 4 seconds. similarly, when the power button is pressed to turn off in the dvd mode, this mode shuts down first and then the tv/dvd/vcr s power is turned off. ? a prohibited icon may appear at the top-right on the tv screen dur- ing operation, warning that a pro- hibited operation has been encoun- tered by the dvd or the disc. ? with dvds that use titles for playback program sig- nals, playback may start from the second title, or it may skip these titles. ? during the playback of a two layered disc, pictures may stop for a moment. this happens when the 1st layer switches to the 2nd layer. this is not a mal- function. general features dvd may contain menus to navigate the disc and access special features. press the appropriate number buttons or use the arrow buttons ( l / k / s / b ) to high- light your selection in the dvd main menu and press the enter button to confirm. notes ? select dvd mode by pressing the select button on the remote control. then, operate the dvd functions. ? unless stated, all operations described are based on remote control use. some operations can be carried out using the menu bar on the tv screen. title menu 1 press the title button. ? the title menu will appear. 2 if the feature is not available, symbol may appear on the tv screen. 3 press the arrow buttons ( l / k / s / b ) to select an item, and the enter button to confirm selection. dvd-v disc menu 1 press the disc menu button. ? the dvd main menu will appear. 2 if the feature is not available, symbol may appear on the tv screen. 3 if disc menu is available on the disc, audio language, subtitle options, chapters for the title and other options will appear for selec- tion. 4 press the arrow buttons ( l / k / s / b ) to select an item, and the enter button to confirm selection. dvd-v calling up a menu screen during playback for dvd-vs ? press the disc menu button to call up the dvd menu. ? press the title button to call up the title menu. note ? contents of menus and corresponding menu opera- tions may vary between discs. refer to the manual accompanying the disc for details. td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 37 38 en 01a11 step by step playback 1 during playback, press the pause button. ? playback will pause and sound will be muted. 2 the disc goes forward by one frame each time the pause button is pressed. 3 to exit step by step playback, press the play button. dvd-v resume 1 during playback, press the stop button. ? resume message will appear on the tv screen. 2 press the play button, playback will resume from the point at which playback was stopped. ? to cancel resume, press the stop button twice. ? if turn off the tv/dvd/vcr, resume function will be cancelled. cd dvd-v 1 during playback, press and hold down the fwd g or rev h button for a few seconds. 2 each press and hold down the fwd g or rev h button repeatedly to select the required speed: x2, x8, x50, x100. ? for audio cds, the speed is fixed at 16. ? for mp3, the speed is fixed at 8. 3 to return to normal playback, press the play button. note for using buttons on the main unit: during playback, press and hold down the skip g / search g buttons or the skip h /search h buttons on the tv/dvd/vcr for a few seconds to begin search in x2 speed. press and hold down again to change speed to x8. repeat this procedure to change to x50 and x100. mp3 cd dvd-v fast forward/reverse search pause 1 during playback, press the pause button. ? playback will pause and sound will be muted. 2 to continue playback, press the play button. cd dvd-v slow forward / slow reverse 1 during playback, press the pause button. 2 press and hold down the fwd g or rev h button for a few seconds. 3 each press and hold down the fwd g or rev h button repeatedly to select the required speed: 1/16, 1/8, 1/2 of the normal playback. 4 to return to normal playback, press the play button. note for using buttons on the main unit: press the pause button, then, press and hold down the skip g / search g buttons or the skip h /search h buttons on the tv/dvd/vcr for a few seconds to begin search in 1/16 speed of the normal playback. press and hold down again to change speed to 1/8. repeat this procedure to change to 1/2. dvd-v zoom the zoom function allows you to enlarge the video image and to pan through the enlarged image. 1 press the zoom button during playback. ? playback will continue. 2 press the zoom button repeatedly to select the required zoom factor: zoom1, zoom2, zoom3, or off. 3 use the arrow buttons ( k / l / s / b ) to move the zoomed picture across the screen. 4 to exit zoom mode, press the zoom button to off. notes ? zooming function does not work while disc menu is shown. ? zooming function is not available on some discs. dvd-v td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 38 39 en 01a11 search function track search there are three ways to begin playback on an audio cd at a specific track. using the number buttons on the remote control 1 press the number buttons to enter the desired track number. ? playback will start at the selected track. ? for single digit tracks (1-9), press a single number (eg. track 3, press 3). ? to play track 26, press +10, 2, 6. using the search mode button 1 press the search mode button. ? the track search display appears. 2 within 30 seconds, select a desired track number using the number buttons on the remote control. ? for single digits press 0 first. ? playback will start at the selected track. using the skip hg buttons during playback, press the skip g button to move the next track. press it repeatedly to skip subsequent tracks. press the skip h button to go back to begin- ning of the current track. press it repeatedly to go to the previous tracks. ? if the skip button is pressed while the playback is paused, the playback will be paused again after skip- ping to the next track. note ? the skip hg buttons are not available when playback is stopped. cd title / chapter search 1 press the search mode button once for the chapter search, twice for the title search during playback. 2 enter the desired chapter/title number using the number buttons on the remote control. ? playback will start at the selected chapter or track. ? press the clear button to erase the incorrect input. ? for single digits press 0 first. dvd-v /2 time search 1 during playback, press the search mode button three times (cd: twice) to display the time search on the tv screen. 2 within 30 seconds, enter a desired disc time using the number buttons on the remote control. ? playback will start at the specified time. ? press the clear button to erase the incorrect input. cd dvd-v marker setup screen use markers to memorise your favorite places on a disc. 1 press the search mode button four times (cd: three times) during playback. ? the display screen and markers will appear on the tv screen. 2 press the arrow buttons ( s / b ) to select 1, 2, 3, 4, 5, 6, 7, 8, 9, or 10 and ensure that ? : - - : - - appears in the display. 3 when reaches the desired point, press the enter button. ? the title or track and elapsed playing time will appear in the tv screen. 4 to return to the marker later, press the search mode button four times (cd: three times) during playback and the arrow but- tons ( s / b ) to choose the desired marker, then press the enter button. notes ? opening the disc tray or turning off the power or select ac at step 2 and press the enter button will erase all markers. ? to clear a marker, using the arrow buttons ( s / b ) , position the cursor on to the marker number to be cleared and press the clear button. ? you can mark up to 10 points. 5 press the search mode or return but- ton to exit. cd dvd-v td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 39 40 en 01a11 special playback function repeat repeat title / chapter to activate the repeat function, press the repeat button during playback. ? the repeat mode changes as described below every time you press the button. dvd-v repeat is available only during playback. chapter title off ( current chapter repeat) ( current title repeat) (repeat off ) notes ? repeat title/chapter is not available with some scenes. ? the repeat setting will be cleared when moving to other title or chapter. repeat track to activate the repeat function, press the repeat button during playback. ? the repeat mode changes as described below every time you press the button. cd track all off ( current track repeat) ( entire disc repeat) (repeat off ) notes ? repeat setting will be cleared when moving to other track. ? repeat playback does not function during repeat a-b playback. repeat a-b 1 press the repeat a-b button at your cho- sen starting point. ? a- appears briefly on the tv screen. 2 press the repeat a-b button again at your chosen end point. ? a-b appears briefly on the tv screen, and the repeat sequence begins. 3 to exit the sequence, press the repeat a- b button. notes ? the repeat a-b section can only be set within the cur- rent title (for dvds), or current track (for audio cds). ? repeat a-b is not available with some scenes in dvd. ? to cancel the a point which was set, press the clear button. ? repeat a-b playback does not function during title, chapter, track or all repeat playback. cd dvd-v program you may determine the order in which tracks will play. 1 in stop mode, press the mode button. ? the program screen will appear. 2 press the arrow button or to select a track, then press the enter button. ? press the clear button to erase the most recently entered program. 3 repeat step 2 until you have selected all the tracks you want to play in the program. 4 press the play button to play the pro- grammed tracks. notes ? while the program is being played back, the stop works as follows. ? press the stop button once and then the play but- ton again, playback will restart from the point where the stop button was pressed. (program continued) ? press the stop button twice and then the play button again, playback will restart from the track in the usual way. (program cleared) ? up to 99 programs can be entered. ? if you like to repeat the current track in the program, press the repeat button repeatedly until track appears during playback. if you like to repeat the entire program press the repeat button repeatedly until all appears during playback. cd total random playback this shuffles the playing order of tracks instead of playback in the sequence. 1 in stop mode, press the mode button twice. ? random screen appears. 2 press the play button to start random playback. note ? if you like to repeat the current track in the random selection, press the repeat button repeatedly until track appears during playback. if you like to repeat the entire random selection press the repeat button repeatedly until all appears during playback. cd play cd [audio] total 0:45:55 random program - - no indication - - random td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 40 41 en 01a11 playing a mp3 disc when a cd with mp3 files is in the tv/dvd/vcr, the mp3 menu will appear on the tv screen in stop mode. 1 in stop mode, press the arrow buttons ( k / l ) to select the desired group track. ? if a group is selected, press the arrow b or enter but- ton to go on to the track selec- tion screen. press the arrow buttons ( k / l ) to choose a track, then press the enter button. ? if a track is selected, press the enter button to start playing tracks. starting from the one you ve just chosen the subsequent tracks will be played. ? choose first play to start playback from the beginning of the listed tracks. ? press the title button to return to the first item. 2 press the stop button to stop playback. notes ? folders are known as groups; files are known as tracks. ? mp3 files are accompanied by icon. ? maximum of 255 folders can be recognized. ? maximum of 256 files can be recognized. ? up to 8 hierarchies can be created. this player recommends the use of files recorded at the below specifications: ? sampling frequency: 44.1khz or 48khz ? constant bit rate: 112kbps ~ 320kbps. 3 mp3 mp3 playback 1 press the search mode button during playback. ? the file list will appear. 2 select a desired track using the arrow but- tons ( k / l / s / b ). ? press the arrow button b when you want to go to the next hierarchy. ? press the arrow button s when you want to go back to the previous hierarchy. 3 press the play button to start playback. notes ? press the search mode button to exit. ? some selections may take a while to be recognized. mp3 track selection random playback 1 in stop mode, press the mode button twice. ? random screen appears. 2 press the play button to start random play- back. mp3 this feature allows you to program an mp3 disc to play in a desired sequence. 1 in stop mode, press the mode button. ? the program screen will appear. 2 select a desired track using the arrow but- tons ( k / l / s / b ). then, press the enter button. ? press the arrow button b when you want to go to the next hierarchy. ? press the arrow button s when you want to go back to the previous hierarchy. ? press the clear button to erase the most recently entered program. 3 repeat step 2 until you have selected all the tracks you want to play in the program. 4 press the play button to start programmed playback. mp3 program td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 41 42 en 01a11 changing the settings audio language the tv/dvd/vcr allows you to select a language during dvd disc (if multi language available) play- back. 1 press the audio button during playback. 2 press the audio button repeatedly to select your desired language. note ? pressing the audio button may not work on some dvds with multiple audio languages (e.g. dvds which allow audio language setting on the disc menu). dvd-v stereo sound mode 1 press the audio button repeatedly during playback to select between stereo, l-ch or r-ch. ? stereo - both right and left channels are active (stereo) l-ch - only left channel is active r-ch - only right channel is active note ? i f the virtual surround setting is on, the sound mode will be fixed to stereo, and can not be changed. cd the dvd allows you to select a language for subtitles during dvd disc (if available) playback. 1 press the subtitle button during playback. 2 press the subtitle button repeatedly to select your desired subtitle language. ? the subtitle language will be displayed on the dis- play bar at the top of the screen. 3 to turn off subtitles, press the subtitle button repeatedly until off appears. notes ? some discs allow audio language setting/subtitle language setting on the disc menu. (operation varies between discs, so refer to the manual accompanying the disc.) ? if the desired language is not shown after pressing the subtitle button several times, the disc does not have subtitles in that language. ? if you choose a language that has a 3 letter language code, the code will be displayed every time you change the subtitle language setting. if you choose any other languages, --- will be displayed instead. (refer to page 44.) dvd-v subtitle language camera angle some dvd discs contain scenes which have been shot simultaneously from various angles. you can change the camera angle when the ( ) icon appears on the screen. 1 press the angle button during playback. ? the selected angle will be displayed on the display bar at the top of the screen. 2 press the angle button repeatedly to select your desired angle. dvd-v adjust the black level settings to make the black parts of the picture brighter. 1 press the mode button during playback. 2 press the enter button to switch off. on: makes the dark parts brighter. off: shows the original picture as recorded. 3 press the mode button twice or the return button to exit. dvd-v black level setting you can enjoy stereophonic visual space on your exist- ing stereo system. 1 press the mode button twice (cd/mp3: once) during playback. 2 press the enter button to set it 1 (natural effect) or 2 (emphasized effect) or off. 3 press the mode or return button to exit. note (for cd play only) ? virtual surround will not be effective if the sound mode is set to something other than stereo. mp3 cd dvd-v virtual surround on off td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 42 43 en 01a11 for dvd-vs 1 press the display button during playback to show current chapter. ? the elapsed and remaining playing time of the current chapter will be displayed. 2 press the display button again to show current title. ? the elapsed and remaining playing time of the cur- rent title will be displayed. 3 press the display button again. ? the bit rate and the current repeat setting will be displayed. ? if you are playing a dual layered disc, the layer num- ber will also be displayed (l0: layer 0 is playing. l1: layer 1 is playing). 4 press the display button again to exit the display. the on-screen information for audio cds 1 press the display button during playback to show the current track. ? the elapsed and remaining playing time of the cur- rent track will be displayed. 2 press the display button again to show current total track. ? the elapsed and remaining playing time of the cur- rent total track will be displayed. 3 press the display button again to exit the display. you can check the information about the current disc by pressing the display button on the remote control. mp3 cd dvd-v 9/49 0:00:00 -0:00:00 for mp3 1 press the display button during playback. ? the name of the file currently in play will be dis- played. 2 press the display button repeatedly to show the track number, the repeat status, and the playback status at the top of the screen. ? will be displayed when repeat play has been selected. t - indicates track repeat g - indicates group (folder) repeat a - indicates disc repeat 3 press the display button again to exit the display. td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 43 44 en 01a11 changing the dvd setup items language setting language options are not available with some discs. 1 press the setup button twice in stop mode so that the dvd setup menu appears. ? if the menu does not appear, press the play button, the stop button, then the setup button twice. 2 press the arrow button b to select cus- tom, then press the enter button. ? custom mode will appear. 3 press the arrow buttons ( s / b ) to select language, then press the enter button to confirm. 4 press the arrow buttons ( k / l ) to select the next items, then press the enter button. audio: ? sets the audio language. subtitle: ? sets the subtitle language. disc menu: ? sets the language for dvd menu. 5 press the arrow buttons ( k / l ) to select a setting, then press the enter button. ? if other is selected on the audio, subtitle or disc menu screen, press four-digit number to enter the code for the desired language. (refer to the language code list below.) ? only the languages supported by the disc can be selected. 6 press the setup button to exit. note ? language setting for audio and subtitle is not avail- able with some discs. then use the audio and the subtitle buttons. details are on page 42. to change the on-screen menus you can access the tv/vcr setup menu by pressing the setup button from the dvd mode. refer to selecting the language on page 16 to changing the on-screen menus. ? in case of selecting from the dvd mode, you cannot select channel set up , v-chip set up , caption , time search , or index search menus. dvd-v language audio original subtitle off disc menu english quick setup tv mode 4:3 letter box dolby digital on if you choose a language that has a 3 letter language code, the code will be displayed every time you change the audio or subtitle language setting on page 42. if you choose any other languages, --- will be displayed instead. (3 letter language code is written in bracket.) language code a-b abkhazian 4748 afar 4747 afrikaans 4752 albanian 6563 amharic 4759 arabic 4764 armenian 5471 assamese 4765 aymara 4771 azerbaijani 4772 bashkir 4847 basque 5167 bengali;bangla 4860 bhutani 5072 bihari 4854 bislama 4855 breton 4864 bulgarian 4853 burmese 5971 byelorussian 4851 c-e cambodian 5759 catalan 4947 chinese [chi] 7254 corsican 4961 croatian 5464 czech 4965 danish [dan] 5047 dutch [dut] 6058 english [eng] 5160 esperanto 5161 estonian 5166 f-h faroese 5261 fiji 5256 finnish [fin] 5255 french [fre] 5264 frisian 5271 galician 5358 georgian 5747 german [ger] 5051 greek [gre] 5158 greenlandic 5758 guarani 5360 gujarati 5367 hausa 5447 hebrew 5569 hindi 5455 hungarian [hun] 5467 i-k icelandic [ice] 5565 indonesian 5560 interlingua 5547 interlingue 5551 inupiak 5557 irish [iri] 5347 italian [ita] 5566 japanese [jpn] 5647 javanese 5669 kannada 5760 kashmiri 5765 kazakh 5757 kinyarwanda 6469 kirghiz 5771 kirundi 6460 korean [kor] 5761 kurdish 5767 language code l-n laothian 5861 latin 5847 latvian;lettish 5868 lingala 5860 lithuanian 5866 macedonian 5957 malagasy 5953 malay 5965 malayalam 5958 maltese 5966 maori 5955 marathi 5964 moldavian 5961 mongolian 5960 nauru 6047 nepali 6051 norwegian [nor] 6061 o-r occitan 6149 oriya 6164 oromo(afan) 6159 panjabi 6247 pashto;pushto 6265 persian 5247 polish 6258 portuguese [por] 6266 quechua 6367 rhaeto-romance 6459 romanian [rum] 6461 russian [rus] 6467 s samoan 6559 sangho 6553 sanskrit 6547 scots gaelic 5350 serbian 6564 serbo-croatian 6554 sesotho 6566 setswana 6660 shona 6560 sindhi 6550 singhalese 6555 siswat 6565 slovak 6557 slovenian 6558 somali 6561 spanish [spa] 5165 sundanese 6567 swahili 6569 swedish [swe] 6568 t tagalog 6658 tajik 6653 tamil 6647 tatar 6666 telugu 6651 thai 6654 tibetan 4861 tigrinya 6655 tonga 6661 tsonga 6665 turkish [tur] 6664 turkmen 6657 twi 6669 u-z ukrainian 6757 urdu 6764 uzbek 6772 vietnamese 6855 volapuk 6861 welsh 4971 wolof 6961 xhosa 7054 yiddish 5655 yoruba 7161 zulu 7267 td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 44 45 en 01a11 audio settings choose the appropriate audio settings for your equip- ment as it only affect during the playback of dvd discs. 1 press the setup button twice in stop mode so that the dvd setup menu appears. ? if the menu does not appear, press the play button, the stop button, then the setup button twice. 2 press the arrow button b to select cus- tom, then press the enter button. ? custom mode will appear. 3 press the arrow buttons ( s / b ) to select audio, then press the enter button to confirm. 4 press the arrow buttons ( k / l ) to select the below items, then press the enter buttons. drc (dynamic range control): ? to compress the range of soft to loud sound. ? the default setting is off. dolby digital: set to on when the unit is connected to a dolby digital decoder. (on: output a dolby digital signal) (off: convert the dolby digital to pcm (2 channel stereo)) ? the default setting is on. down sampling: ? set to on when outputting in 48 khz. ? the default setting is on. when playing disc with copyright protection ? if you select off, copyright protection will be acti- vated and sound will be down sampled at 48khz. 5 press the setup button to exit. quick audio drc off dolby digital on down sampling on you can change certain aspects of the dvd display screens and on-screen messages on the tv screen. 1 press the setup button twice in stop mode so that the dvd setup menu appears. ? if the menu does not appear, press the play button, the stop button, then the setup button twice. 2 press the arrow button b to select cus- tom, then press the enter button. ? custom mode will appear. 3 press the arrow button ( s / b ) to select dis- play, then press the enter button to confirm. 4 press the arrow buttons ( k / l ) to select the below items, then press the enter button. tv mode: ? press the arrow buttons ( k / l ) for an item selection, then press the enter button. ? select 4:3 letter box for a black bars appears on top and bottom of the screen. ? select 4:3 pan & scan for a full height picture with both sides trimmed. ? the default setting is 4:3 letter box. angle icon: ? press the enter button repeatedly to turn angle icon on or off. ? the default setting is on. auto power off: ? press the enter button repeatedly to turn auto power off on or off. ? the default setting is on and it will turn the tv/dvd/vcr to off automatically after 15 minutes of no use. 5 press the setup button to exit. quick dvd-v display setting display tv mode 4:3 letter box angle icon on auto power off on quick setup tv mode 4:3 letter box dolby digital on quick setup tv mode 4:3 letter box dolby digital on td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 45 46 en 01a11 46 control levels ? all all parental lock is cancelled. ? level 8 dvd software of any grade (adult/general/children) can be played back. ? levels 7 to 2 only dvd software intended for general use and children can be played back. ? level 1 only dvd software intended for children can be played back, with those intended for adult and general use prohibited. parental control parental control limits the disc viewing that exceed your settings. (with a password or playback will stop.) this feature allows you to prevent discs with alterna- tive scenes from being played by your children. dvd-v parental level parental level allows you to set the rating level of your dvd discs. playback will stop if the disc s rat- ings exceed the level you set. 1 press the setup button twice in stop mode so that the quick setup menu appears. ? if the menu does not appear, press the play button, the stop button, then the setup button twice. 2 press the arrow button b to select cus- tom, then press the enter button. 3 press the arrow buttons ( s / b ) to select parental, then press the enter button. 4 enter your four-digit password then press the enter button. 5 press the arrow buttons ( k / l ) to select parental level, then press the enter button. 6 press the arrow buttons ( k / l ) to select the desired level. 7 press the setup button to exit notes ? when doing this for the first time, enter any 4 digits. (except for 4737) that number will be used as the password.(in the event you forget the password, see below) ? to change the password, press the arrow buttons ( k / l ) to select change at step 5, then press the enter button. enter the four-digit pass-word, then press the enter button. ? with some dvds, it may be difficult to find if they are compatible with parental lock. be sure to check if the parental lock function operates in the way that you have set. ? record the password in case you forget it. if you forget the password 1 press the number buttons 4, 7, 3, 7 at step 4. then enter your new password. ? password will be cleared and parental level will be set to all. 2 proceed the above steps 5-7 again. parental parental level all quick setup tv mode 4:3 letter box dolby digital on td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 46 47 en 01a11 sometimes a performance problem can be easily solved by checking seemingly apparent but often overlooked possibilities. before arranging for service, check these items. it could save your time and money. tv/vcr mode troubleshooting guide problem corrective action no picture and sound. make sure the ac cord is connected to an ac outlet. check antenna connection. press the select button on the remote control to select tv mode. then try other tv feature. let the tv/dvd/vcr program its tuner memory. no picture or poor picture on adjust direction or replace antenna. tv/dvd/vcr. adjust picture controls. no sound or poor sound. adjust volume control on remote control or main unit. press the mute button to restore sound. bars on screen if outside antenna is being used, check for broken wire. check for local interference. picture distorted or blurred try a new channel, if ok, then possible station trouble. if outside antenna is being used, check for broken wire. picture rolls vertically try a new channel, if ok, then possible station trouble. lines or streaks in picture if outside antenna is being used, check for broken wire. check for local interference. no color try a new channel, if ok, then possible station trouble. is antenna connected to terminal on the back of the set? if outside antenna is being used, check for broken wire. adjust color control. poor reception on some channels try a new channel, if ok, then possible station trouble. ghosts in picture is antenna connected to terminal on the back of the set? if outside antenna is being used, check for broken wire. check for local interference. weak picture try a new channel, if ok, then possible station trouble. is antenna connected to terminal on the back of the set? if outside antenna is being used, check for broken wire. adjust contrast & bright control. sound ok, picture poor try a new channel, if ok, then possible station trouble. is antenna connected to terminal on the back of the set? if outside antenna is being used, check for broken wire. check for local interference. adjust contrast & bright control. if the tv/dvd/vcr does not perform properly when operated as instructed in this owner s manual, check the player, consulting the following checklist. problem corrective action no power. make sure the power plug is connected to an ac outlet. make sure the power is turned on. the tv/dvd/vcr does not check if the power plug is connected to an ac outlet. respond to the remote control. check the batteries in the remote control. aim the remote control directly at the remote sensor. if necessary, remove all the obstacles between the sensor and the remote. you have to be within 23 feet of the tv/dvd/vcr. check if the correct mode is selected. if not switch the mode by pressing the select button on the remote control,whichever you need. td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 47 48 en 01a11 closed caption problem possible remedy my tv/dvd/vcr is showing you are watching a live broadcast and spelling errors made by the captions that are misspelled. closed captioning production company may pass through uncorrected. a prerecorded program will not show any misspelled words because of the normal time available for editing the captions. my tv/dvd/vcr will not show captions that are delayed a few seconds behind the actual the text dialogue are common for live broadcast. most captioning production in its entirety or there is a delay of companies can display a dialogue to a maximum of 220 words what is being said. per minute. if a dialogue exceeds that rate, selective editing is used to insure that the captions remain up-to-date with the current tv screen dialogue. my captions are scrambled with interference caused by building, power lines, thunderstorms, etc. white boxes on the tv screen. may cause scrambled or incomplete captions to appear. my program guide listed a tv show broadcasters may at times use a time compression process to speed as being closed captioned but none up the actual program so that additional advertising time can be of the captions were displayed. given. since the decoder cannot read the compressed information, captions will be lost. my prerecorded video tape does not the video tape was either an illegal copy or the tape duplicating show any captions. the tape box company accidentally left out the captioning signals during the mentions it being closed captioned. copying process. my tv screen shows a black box you are in the text mode. select caption mode to caption on certain channels. [off]. problem corrective action picture ok, sound poor try a new channel, if ok, then possible station trouble. check for local interference. timer recording is not possible. make sure the timer recording is set correctly. make sure the power is off. make sure the tv/dvd/vcr clock is set correctly. cannot go into record mode. make sure the tape has an erase-prevention tab. if need, cover the hole with plastic tape. playback picture is partially noisy. adjust tracking control for a better picture using the channel button k or l on the tv/dvd/vcr. no picture but the audio is ok in head cleaning may be necessary. refer to auto head playback. cleaning on page 50. no operation by infrared remote make sure the ac cord is connected to an ac outlet. control. check batteries in remote control. video or color fades in and out you can not copy a copyrighted video tape. you are experiencing when making a copy of a video tape . copy guard protection. different color marks on screen. magnetism from nearby appliances and geomagnetism might affect the color of the tv picture. move the tv/dvd/vcr away from the appliances, the tv/dvd/vcr can repair itself automatically. if you want to repair immediately, turn off using the power button, then turn it on again 30 minutes or so later (27 model), or unplug the power cord, then plug it in again 30 minutes or so later (19 model). td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 48 49 en 01a11 notes: some functions are not available in specific modes, but this is not a malfunction. read the description in this owner s manual for details on correct operations. playback from a desired track and random playback are not available during program playback. problem corrective action no picture. connect the video cables firmly. insert a correct video disc that plays on this tv/dvd/vcr. press the select button on the remote control to select dvd mode. then, try other dvd feature. disc cannot be played . insert the disc. clean the disc. place the disc correctly, with the label side up. cancel the parental lock or change the control level. no sound . connect the audio cables firmly. turn the power of the audio component on. correct the audio output settings. correct the input settings on the audio component. no dts audio is output . this tv/dvd/vcr does not support dts audio. this is not a mal- function. distorted picture . there are some cases where pictures may be slightly distorted, which are not a sign of a malfunction. although pictures may stop for a moment, this is not a malfunction. audio or subtitle language the selected language is not available for audio or subtitles on the dvd. does not match the set up this is not a malfunction the camera angle cannot be changed the dvd does not contain sequences recorded from different camera angles. this is not a malfunction audio or subtitle language cannot be the dvd does not contain audio source or subtitles in the selected changed language. this is not a malfunction. prohibited icon appears on the that operation is prohibited by the player or the disc. screen, prohibiting an operation this is not a malfunction. cd sound dropout scratched disc. replace the disc with unscratched one. no cd reproduction dvd picture dropout dvd picture freeze dvd picture in mosaic no dvd reproduction dvd mode td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 49 50 en 01a11 en 01a11 cabinet cleaning wipe the front panel and other exterior surfaces of the tv/dvd/vcr with a soft cloth immersed in lukewarm water and wrung dry. never use a solvent or alcohol. do not spray insec- ticide liquid near the tv/dvd/vcr. such chemi- cals may cause damage and discoloration to the exposed surfaces. auto head cleaning automatically cleans video heads as you insert or remove a cassette, so you can see a clear picture. playback picture may become blurred of interrupt- ed while the tv program reception is clear. dirt accumulated on the video heads after long periods of use, or the usage of rental or worn tapes can cause this problem. if a streaky or snowy picture appears during play- back, the video heads in your tv/dvd/vcr may need to be cleaned. 1. please visit your local audio/video store and pur- chase a good quality vhs video head cleaner. 2. if a video head cleaner does not solve the prob- lem, please call our help line at 1-800-256-2487, to locate an authorized service center. notes: remember to read the instructions included with the video head cleaner before use . clean video heads only when problems occur. servicing should your tv/dvd/vcr become inoperative, do not try to correct the problem by yourself. there are no user-serviceable parts inside. turn off, unplug the power cord, and please call our help line at 1-800-256-2487, to locate an authorized service center. if the laser optical pickup unit is dirty if the player still does not perform properly when it is operated while referring to the relevant sections and to "troubleshooting guide" in this owner's manual, the laser optical pickup unit may be dirty. consult your dealer or an authorized service center for inspection and cleaning of the laser optical pickup unit. use discs which have the following logos on them. (optical audio digital discs.) handle the discs so that fingerprints and dust do not adhere to the surfaces of the discs. always store the disc in its protective case when it is not used. disc handling to clean-off, use a soft cloth. do not use a hard cloth since this will mar the disc. wipe the disc in a straight line from center to edge. never wipe with a circular motion. do not use detergent or abrasive cleaning agents. maintenance recordable rewritable td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 50 51 en 01a11 crt [19 inch model] : 19 inch in-line gun, 90 ? deflection tube [27 inch model] : 27 inch in-line gun, 110 ? deflection tube television system : ntsc-m closed caption system : 15.119/fcc video heads : rotary four-head tape width : 1/2 inch tape speed sp : 33.40mm/sec. lp : 16.67mm/sec. slp : 11.12mm/sec. tuner channel tv vhf low : #2~#6 tv vhf high : #7~#13 tv uhf : #14~#69 catv vhf : 5a mid band : a5~a1, a~i super band : j~w hyper band : w+1~w+84 product type: dvd player discs: dvd video, audio cd output signal format: ntsc color frequency response (out put jack) dvd (linear sound): 20 hz to 22 khz (sample rate: 48 khz) 20 hz to 44 khz (sample rate: 96 khz) cd: 20 hz to 20 khz signal-to-noise ratio (s/n ratio)(out put jack) cd: 75 db (eiaj) dynamic range (out put jack) dvd (linear sound): 85 db cd: 84 db (eiaj) total distortion factor cd: 0.07% (eiaj) wow and flutter: below the measurement limitation (+/-0.001% w peak) (eiaj) designs and specifications are subject to change without notice. if there is a discrepancy between languages, the default language will be english. tv/vcr dvd general specifications electrical specifications sound output: 2 speakers, 1w, 8 ohm other specifications terminals antenna input: vhf/uhf/catv 75 ohm unbalanced (f-type) video input: rca connector [ 1 audio l/r input: rca connector [ 2 headphone: 1/8 stereo (3.5 mm) coaxial digital audio output: one pin jack, 500m vpp (75 ohm) analog audio l/r output : rca connector [ 2 remote control: digital encoded infrared light system operating temperature: 5 c to 40 c (41 f~104 f) power requirements: ac 120v, 60hz [19 inch model] power consumption (maximum): 90w picture tube: 19" dimensions: h:19-11/16 (500mm) w:21-7/8 (556mm) d:18-3/4 (476.5mm) weight: 45.2 lbs (20.5kg) [27 inch model] power consumption (maximum): 125w picture tube: 27" dimensions: h:25-1/2 (648mm) w:26-9/16 (675mm) d:19-11/16 (500mm) weight: 86 lbs (39.0kg) specifications td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 51 52 es 0c28 indice controles de operaci? y funciones . . . . . 52 panel frontal del televisor/dvd. . . . . . . . . . 52 mando a distancia . . . . . . . . . . . . . . . . . . . . . . . . . 52 vista posterior . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52 preparaci n para la utilizaci n . . . . . . . . . . 53 conexiones de antena/cable . . . . . . . . . . . . . . 53 conexi n a tomas de entrada externa. . . . 53 para insertar las pilas . . . . . . . . . . . . . . . . . . . . 54 modo de entrada externa . . . . . . . . . . . . . . . . 54 conexi n a un sistema est ? reo . . . . . . . . . . . . 54 conexi n a un amplificador est ? reo equipado con tomas de entrada digital, platina md o platina dat (para dvd). . . . . . . . . 54 conexi n a un decodificador dolby digital (para dvd) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54 secci? de tv/vcr preparaci n para la utilizaci n . . . . . . . . . . 54 preajuste de canales. . . . . . . . . . . . . . . . . . . . . . 55 c mo borrar (agregar) canales . . . . . . . . . . 55 secci n de dvd reproducci n b sica . . . . . . . . . . . . . . . . . . . . . . 55 controles de operaci? y funciones panel frontal del televisor/dvd consulte la figura 1 de la p ? gina 9 mando a distancia consulte la figura 2 de la p ? gina 9 vista posterior consulte la figura 3 de la p ? gina 10 1. bot ? n power presione este bot ? n para conectar y desconectar la ali- mentaci ? n. 2. botones volume x / y presione estos botones para controlar el nivel de volumen del dvd y el televisor. 3. botones skip (para dvd) presione el bot ? n correspondiente una vez para omitir cap ? tulos o pistas y desplazarse a un punto espec ? fico. mantenga el bot ? n presionado para cambiar la veloci- dad de reproducci ? n en avance o retroceso. 4. bot ? n play inicia la reproducci ? n del contenido del disco o cinta. 5. bot ? n stop detiene la reproducci ? n del disco. 6. bot ? n open/close presione este bot ? n para insertar discos en la bandeja o retirarlos de ella. 7. bandeja de carga del disco 8. indicador dvd se ilumina durante el modo dvd. 9. bot ? n select presione este bot ? n para cambiar al modo tv/vcr, modo de entrada externa o modo de dvd. 10. indicador tv/vcr se ilumina durante el modo tv/vcr. 11. botones channel k / l utilice estos botones para seleccionar canales memorizados. 12. indicador de grabaci ? n parpadea durante la grabaci ? n. se ilumina durante el modo de espera de grabaci ? n controlada por temporizador. 13. bot ? n rec/otr (record) presione este bot ? n para grabar manualmente. este bot ? n tambi ? n activa la funci ? n de grabaci ? n instan- t ? nea (otr). (la funci ? n otr s ? lo est ? disponible durante el modo tv/vcr.) 14. bot ? n rew (para tv/vcr) presione este bot ? n para rebobinar la cinta o para ver la imagen r ? pidamente en direcci ? n de retroceso durante el modo de reproducci ? n. (b ? squeda en direc- ci ? n de retroceso) 15. bot ? n fwd (para tv/vcr) presione este bot ? n para adelantar r ? pidamente la cinta o para ver la imagen r ? pidamente en direcci ? n de avance durante el modo de reproducci ? n. (b ? squeda en direcci ? n de avance) 16. bot ? n stop/eject presione este bot ? n para detener la cinta. presi ? nelo en el modo de parada para retirar la cinta del televisor/dvd/videograbadora. 17. ventanilla del sensor de mando a distancia 18. toma headphone para conectar auriculares (no suministrados) y escuchar en privado. 19. toma de entrada video conecte aqu ? la toma de salida de v ? deo de una videoc ? mara o de una videograbadora. 20. tomas de entrada audio l/r conecte aqu ? las tomas de salida de audio de una videoc ? mara o de una videograbadora. 21. compartimiento del cassette 22. bot ? n picture presione este bot ? n para ajustar la imagen. 23. botones num ? ricos modo tv: presione dos botones para acceder directamente al canal deseado. no olvide presionar 0 antes de elegir un canal de un solo d ? gito. bot ? n +100 presione este bot ? n para seleccionar canales de tele- visi ? n por cable cuyo n ? mero sea igual o superior a 100. modo dvd: presione este bot ? n para introducir el n ? mero deseado. bot ? n +10 presione este bot ? n para introducir n ? meros iguales o mayores que 10 . 24. bot ? n pause hace una pausa en la reproducci ? n del disco o cinta. 25. bot ? n speed presione este bot ? n para seleccionar la velocidad de grabaci ? n deseada: sp/slp. 26. bot ? n c.reset presione este bot ? n para poner el contador en 0:00:00. presi ? nelo tambi ? n para cancelar un ajuste de progra- ma de temporizador. 27. bot ? n display modo tv/vcr: para visualizar el contador o el n ? mero del canal y la fecha actual en la pantalla del televisor. modo dvd: indica el estado actual en la pantalla del televisor para fines de comprobaci ? n. 28. bot ? n setup presione este bot ? n para activar o salir del modo de men ? s de televisor o configuraci ? n de dvd. 29. bot ? n title para visualizar el men ? de t ? tulos. td853/953es.qx33 03.2.28 10:56 pm page 52 53 es 0c28 30. bot ? n clear para cancelar ajustes. 31. bot ? n mode activa el modo de reproducci ? n programada o el modo de reproducci ? n aleatoria. 32. bot ? n search mode presione este bot ? n para localizar un punto deseado. 33. bot ? n audio presione este bot ? n para seleccionar un idioma de audio o el modo de sonido deseado. 34. bot ? n subtitle presione este bot ? n para seleccionar el idioma de subt ? - tulos deseado. 35. bot ? n repeat repite la reproducci ? n del disco, t ? tulo, cap ? tulo o pista actual. 36. bot ? n angle (modo dvd) presione este bot ? n para cambiar el ? ngulo de la c ? mara y ver la secuencia que se est ? reproduciendo desde un ? ngulo diferente. 37. bot ? n a-b repeat repite la reproducci ? n de una secci ? n seleccionada. 38. bot ? n return permite volver a la operaci ? n anterior en el modo de configuraci ? n de dvd. 39. bot ? n enter presione este bot ? n para establecer un ajuste. 40. botones de flechas modo tv/vcr: presione estos botones para seleccionar un modo de ajuste en el men ? que aparece en la pantalla del televisor. presi ? nelos tambi ? n para seleccionar opciones o establecer ajustes en un men ? en particular. modo dvd: use estos botones para hacer ajustes mientras observa la imagen en la pantalla del televisor. 41. bot ? n disc menu muestra los men ? s contenidos en el dvd. 42. bot ? n zoom ampl ? a parte de la imagen reproducida de un dvd. 43. bot ? n mute suprime la salida de sonido. presi ? nelo de nuevo para restablecer el sonido. 44. bot ? n sleep utilice este bot ? n para ajustar el temporizador de dormir. 45. bot ? n select presione este bot ? n para cambiar entre los modos tv/vcr y dvd. el modo seleccionado (tv/vcr o dvd) se visualiza en el indicador del panel delantero. 46. toma de entrada ant. con ? ctela a una antena, sistema de televisi ? n por cable o sistema de sat ? lite. 47. cable de alimentaci ? n con ? ctelo a una toma de ca est ? ndar (120 v, /60 hz). nota: antes de conectar el cable de alimentaci ? n a una toma de ca est ? ndar, ret ? relo del gancho para evitar da ? arlo. 48. toma de salida de audio digital coaxial con ? ctela solamente a la entrada digital de un amplifi- cador externo o decodificador de audio de dvd. 49. toma de salida audio l/r con ? ctela a la entrada de audio anal ? gico de un ampli- ficador o decodificador externo. preparaci n para la utilizaci n conexiones de antena/cable antenas separadas de vhf/uhf en algunas zonas ser ? necesario utilizar una antena exterior. televisi n por cable sin caja de convertidor/decodificador utilice esta conexi ? n si su sistema de televisi ? n por cable se conecta directamente a su televisor/dvd/ videograbadora, sin una caja de convertidor. con esta conexi ? n podr ? : 1) utilizar el mando a distancia del televisor/dvd/ videograbadora para seleccionar canales. 2) programar uno o m ? s canales decodificados para grabaci ? n autom ? tica controlada por temporizador. nota: este televisor/dvd/videograbadora s lo puede grabar el canal que se est ? viendo. televisi n por cable con caja de convertidor/decodificador o caja de sat ? lite si su compa ?? a de televisi ? n por cable le suministra una caja de convertidor o si utiliza un sistema de sat ? lite, podr ? utilizar la conexi ? n b ? sica que se muestra en la ilustraci ? n. al utilizar esta conexi ? n, tambi ? n podr ? grabar canales codificados. sin embargo, la selecci ? n de los canales deber ? hacerse con la caja de convertidor o con la caja de sat ? lite. esto significa que no es posible cambiar de canal utilizando el mando a distancia del televisor/dvd/ videograbadora. la grabaci ? n en ausencia (controlada por temporizador) est ? limitada a un canal a la vez. para grabar un canal codificado/decodificado 1. ajuste el selector de canales del televisor/dvd/videograbadora al canal de salida de la caja de convertidor de televisi ? n por cable o caja de sat ? lite. (ej., ch3) 2. seleccione el canal que desea grabar en la caja de convertidor de televisi ? n por cable o caja de sat ? lite. nota para el instalador de sistemas catv esta nota tiene la finalidad de llamar la atenci ? n del instalador de sistemas catv para que tenga en cuenta el art ? culo 820-40 de la nec, que pro- porciona recomendaciones para hacer una conex- i ? n a tierra apropiada y, en particular, especifica que la tierra del cable debe conectarse al sistema de puesta a tierra del edificio, tan cerca del punto de entrada del cable como sea posible. consulte la figura 4 de la p ? gina 11 conexi n a tomas de entrada externa cuando vea un programa grabado en otra fuente (videograbado- ra o videoc ? mara), utilice las tomas de entrada de audio/v ? deo de la parte delantera del televisor/dvd/videograbadora. conecte las tomas de salida de audio/v ? deo de otra fuente a las tomas audio l/r y video de este televisor/dvd/videograbadora. luego, presione los botones channel k / l hasta que aparezca "aux" en la pantalla. nota: cuando conecte una videograbadora monof ? nica (otra fuente) a este televisor/dvd/videograbadora, conecte la toma de salida de audio de la videograbadora monof ? nica (otra fuente) a la toma audio l de este televisor/dvd/videograbadora. el audio saldr ? igual- mente por los canales izquierdo y derecho. consulte la figura 5 de la p ? gina 12 td853/953es.qx33 03.2.28 10:56 pm page 53 secci? de tv/vcr 54 es 0c28 modo de entrada externa al usar una se ? al de entrada externa (otra videograbado- ra o una videoc ? mara), conecte los cables de salida de audio/v ? deo del equipo externo a las tomas audio l/r in/ video in de su televisor/dvd/videograbadora. luego, presione los botones channel k / l hasta que aparezca "aux" en la pantalla. conexi n a un decodificador dolby digital (para dvd) si utiliza este televisor/dvd/videograbadora para reproducir un disco dvd grabado en formato de sonido envolvente dolby digital de 5,1 canales, el televisor/dvd/videograbadora emitir ? un flujo de datos dolby digital desde su toma de salida de audio digital coaxial. si conecta el reproductor a un decodificador dolby digital, podr ? disfrutar de una tonalidad m ? s convincente y real, con un sonido envolvente potente y de alta calidad similar al de los cines. utilice cables digitales coaxiales de audio disponibles en el comercio especializado para hacer las conexiones de audio. notas: aseg ? rese de desconectar la alimentaci ? n de todos los componentes del sistema antes de conectar otro componente. consulte los manuales de instrucciones de los componentes que va a conectar al televisor/dvd/videograbadora. si conecta un decodificador dolby digital, ajuste la funci ? n dolby digital a on para salida de audio en el modo de configuraci ? n. a menos que se haga la conexi ? n a un decodifi- cador dolby digital, ajuste la funci ? n dolby digital a off para salida de audio en el modo de configuraci ? n. la reproducci ? n en un televisor/dvd/videograbadora utilizando ajustes incorrectos puede generar ruido y distorsi ? n, y tambi ? n puede causar da ? os a los altavoces. fabricado bajo licencia de dolby laboratories. dolby y el s ? mbolo de la d doble son marcas de f ? brica de dolby laboratories. 1) abra la cubierta del compartimiento de las pilas empujando la cubierta del mando a distancia en el sentido de la flecha. 2) inserte 2 pilas "aa" en el compartimiento de las pilas, en el sentido indicado por las marcas de polaridad (+/-). 3) vuelva a poner la cubierta. para insertar las pilas conexi n a un sistema est ? reo notas: aseg ? rese de desconectar la alimentaci ? n de todos los componentes del sistema antes de conectar otro componente. consulte el manual de instrucciones de su sistema est ? reo y de cualquier otro componente que vaya a conectar al televisor/dvd/videograbadora. conexi n a un amplificador est ? reo equipado con tomas de entrada digital, platina md o platina dat (para dvd) utilice un cable digital coaxial de audio de venta en el comercio especializado para hacer las conexiones de audio. conexi ? n a un amplificador equipado con tomas de entrada digital, platina md o platina dat. notas: la fuente de audio de un disco grabado en formato de sonido envolvente dolby digital de 5,1 canales no se puede grabar como sonido digital mediante una platina md o dat. aseg ? rese de desconectar la alimentaci ? n de todos los componentes del sistema antes de conectar otro componente. consulte los manuales de instrucciones de los componentes que va a conectar al televisor/dvd/videograbadora. ajuste la funci ? n dolby digital a off para salida de audio en el modo de configuraci ? n. la repro- ducci ? n en un televisor/dvd/videograbadora uti- lizando ajustes incorrectos puede generar ruido y distorsi ? n, y tambi ? n puede causar da ? os a los altavoces. preparaci n para la utilizaci n puede programar el sintonizador para explorar todos los canales que pueda recibir en su zona. nota: la programaci ? n de la memoria de canales no es necesaria cuando se hace la conexi ? n a una caja de televisi ? n por cable o a una caja de sat ? lite. simplemente ajuste el selector de canales del televi- sor/dvd/videograbadora a la posici ? n correspondi- ente al canal de salida de la caja de televisi ? n por cable o caja de sat ? lite (ej., ch3). luego, seleccione el canal que desea ver en la caja de televisi ? n por cable o en la caja de sat ? lite. consulte la figura 6 de la p ? gina 13 consulte la figura 7 de la p ? gina 13 consulte la figura 8 de la p ? gina 14 td853/953es.qx33 03.2.28 10:56 pm page 54 55 es 0c28 c mo borrar (agregar) canales 2 seleccione agregar/borrar presione el bot ? n de flecha k o l para se ? alar agregar/borrar . presione el bot ? n enter. 3 introduzca el n ? mero del canal deseado presione el bot ? n de flecha k o l hasta que aparez- ca el n ? mero del canal deseado. (tambi ? n puede uti- lizar tambi ? n los botones num ? ricos o los botones channel k / l para introducirlo.) (ejemplo: ch8) 4 borre el canal de la memoria o agr ? guelo a ella presione el bot ? n enter. el n ? mero del canal seleccionado se ilumina de color rojo. el canal de borra de la memoria. para borrar otro canal, repita los pasos [3] y [4]. si vuelve a presionar el bot ? n enter, el canal se memorizar ? de nuevo. presione el bot ? n return para hacer que el tele- visor/videograbadora vuelva al men ? setup. 5 salga del modo de preajuste de canales presione el bot ? n setup del mando a distancia para volver al modo de televisor. nota: para confirmar que los canales han sido bor- rados o agregados, presione el bot ? n channel k o l . canal agregado: se enciende en azul. canal borrado: se enciende en rojo. puede borrar de la memoria los canales que ya no recibe o que ve muy raramente. (por supuesto, puede volver a agregar a la memoria los canales que haya borrado de la misma.) 1 seleccione ajuste de canal presione el bot ? n setup del mando a distancia. presione el bot ? n de flecha k o l para se ? alar ajuste de canal . luego, presione el bot ? n enter. tv/vcr preajuste de canales 1 conecte el cable de alimentaci ? n del televi- sor/dvd/videograbadora conecte el cable de alimentaci ? n del televisor/dvd/videograbadora nota: si aparecen algunos d ? gitos en la esquina de la pan- talla, presione el bot ? n power sin desconectar el cable de alimentaci ? n. 2 encienda el televisor/dvd/videograbadora presione el bot ? n power para encender el televi- sor/dvd/videograbadora. 3 seleccione english , espa ? ol o fran ? ais presione el bot ? n enter para seleccionar "eng- lish" = ingl ? s, "espa ? ol" o "fran ? ais" = franc ? s. "[ ]" indica el idioma seleccionado. 4 inicie el preajuste autom ? tico presione el bot ? n de flecha k o l para se ? alar "autopreseleccion". luego, presione el bot ? n enter. el sintonizador explora y memoriza todos los canales activos de su zona. notas: el televisor/dvd/videograbadora distingue entre los canales de tv est ? ndar y los canales de tele- visi ? n por cable. si desea reproducir o grabar una cinta de v ? deo antes de preajustar el sintonizador, deber ? pre- sionar el bot ? n setup del mando a distancia. el televisor/dvd/videograbadora puede memorizar canales de tv como canales de catv si las condi- ciones de recepci ? n no son buenas. si esto sucede, vuelva a intentar la acci ? n auto memo cuando las condiciones de recepci ? n mejoren. 5 una vez finalizada la exploraci ? n el sintonizador se detiene en el canal memorizado m ? s bajo. si desea recuperar los canales selecciona- dos, podr ? seleccionar los canales directamente con los botones num ? ricos o los botones channel k o l del mando a distancia. tv/vcr secci n de dvd reproducci n b sica para empezar ? conecte la alimentaci ? n del amplificador y otros componentes, si es necesario. 1 presione el bot ? n power. ? la alimentaci ? n se conectar ? . 2 presione el bot ? n open/close para abrir la bandeja de carga del disco. 3 ponga el disco deseado en la bandeja, con la etiqueta hacia arriba. 4 presione el bot ? n play. ? la bandeja se cerrar ? autom ? ticamente y la repro- ducci ? n comenzar ? desde el primer cap ? tulo o pista del disco. si la reproducci ? n no comienza autom ? ti- camente, presione el bot ? n play. ? cuando reproduzca un dvd que tenga grabado un men ? de t ? tulos, el men ? podr ? aparecer en la pan- talla. 5 presione el bot ? n stop para detener la reproducci ? n. cd dvd-v td853/953es.qx33 03.2.28 10:56 pm page 55 printed in malaysia 0emn02182 td853ud/td953ud limited warranty funai corp. will repair this emerson product, free of charge in the usa in the event of defect in materials or workmanship as follows: duration: parts: funai corp. will provide parts to replace defective parts without charge for one (1) year from the date of original retail purchase. two (2) years for picture tube. certain parts are excluded from this warranty. labor: funai corp. will provide the labor without charge for a period of ninety (90) days from the date of original retail purchase. limits and exclusions: this warranty is extended only to the original retail purchaser. a purchase receipt or other proof of original retail purchase will be required together with the product to obtain service under this warranty. this warranty shall not be extended to any other person or transferee. this warranty is void and of no effect if any serial numbers on the product are altered, replaced, defaced, missing or if service was attempted by an unauthorized service center. this funai corporation limited warranty does not apply to any product not purchased and used in the united states. this warranty only covers failures due to defects in material or workmanship which occurs during normal use. it does not cover damage which occurs in shipment, or failures which are caused by repairs, alterations or product not supplied by funai corp., or damage which results from accident, misuse, abuse, mishandling, misapplication, alteration, faulty installation, improper maintenance, commercial use such as hotel, rental or office use of this product or damage which results from fire, flood, lightning or other acts of god. this warranty does not cover packing materials, any accessories (except remote control), any cosmetic parts, complete assembly parts, demo or floor models. funai corp. and its representatives or agents shall in no event be liable for any general, indirect or consequential damages arising out of or occasioned by the use of or the inability to use this product. this warranty is made in lieu of all other warranties, express or implied, and of all other liabilities on the part of funai, all other warranties including the warranty of merchantability, and fitness for a particular purpose, are hereby disclaimed by funai and its representatives in the united states. all warranty inspections and repairs must be performed by a funai authorized service center. this warranty is valid when the unit is carried-in to funai authorized service facility. important: this limited warranty gives you specific legal rights, you may have other rights that vary from state to state, if, at any time during the warranty period, you are unable to obtain satisfaction with the repair of this product, please contact funai corp. attention: funai corp. reserves the right to modify any design of this product without prior notice. to locate your nearest emerson authorized service center or for general service procedure, please call 1-800-256-2487 or write to the following: funai corporation, inc. customer service 100 north street; teterboro, nj 07608 tel :1-800-256-2487 http://www.funai-corp.com please do not ship your unit to the teterboro address. td853ud/953(p36-52).qx33 03.2.28 10:54 pm page 52 |
Price & Availability of EWC27T3
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |